Daewoo Nexia

since 1994 of release

Repair and car operation

Deu Neksiya
+ Maintenance instruction
+ Maintenance
- Engine
   2.1. Technical characteristics
   2.2. Greasing system
   2.3. Maintenance and engine repair
   2.4. Compression check
   2.5. Dismantle and engine installation assembled
   2.6. Engine support
   2.7. Inlet collector and laying
   2.8. Final collector and laying
   2.9. Cover of the case of a cam-shaft
   2.10. Pulley of a cranked shaft
   2.11. Forward cover of a gear belt
   2.12. Camshaft cogwheel
   2.13. Cogwheel of a cranked shaft
   2.14. Back cover of a gear belt
   2.15. Adjustment of a tension of a gear belt
   2.16. Verification of the angular provision of a camshaft
   2.17. Forward consolidation of a cranked shaft
   2.18. Camshaft. Levers. Hydrojacks of gaps
   2.19. Klapannye of a spring. Consolidations of cores of valves
   2.20. Head of cylinders. Camshaft case
   2.21. Repair of a head of the block of cylinders
   2.22. Dismantle of valves
   2.23. Directing plugs of valves
   2.24. Expansion of openings of plugs
   2.25. Valves
   2.26. Klapannye of a spring
   2.27. Saddles of valves
   2.28. Consolidations of valves
   2.29. Height of a core of the valve concerning a head of the block of cylinders
   + 2.30. Pushers of valves with hydrojacks of gaps
   2.31. Oil pallet
   2.32. A reception branch pipe with the oil filter
   2.33. Oil pump
   2.34. Repair of the oil pump
   2.35. Pistons and rods
   2.36. Flywheel. Back consolidation of a cranked shaft
   2.37. Cranked shaft
   2.38. Rods and radical bearings
   2.39. Replacement of loose leaves
   2.40. Piston group and rods
   2.41. Piston fingers and rings
   2.42. Block of cylinders
   2.43. Installation of pistons
   2.44. Disk balancing with a gear wreath
   2.45. Repair of carving openings
   + 2.46. Diagnostics of malfunctions of the engine
+ 3. Engine (two top camshafts)
+ cooling System
+ Toplevnaya and exhaust systems
+ Electric chain
+ 7. Ignition system
+ 8. Electronic control unit and sensors
+ Transmission
+ 10. Five-speed transmission and main RPO MM5 broadcast
+ 11. Automatic Transmission
+ Steering
+ Running gear
+ 14. Forward suspension bracket
+ 15. Drive of forward wheels
+ 16. Back suspension bracket
+ Brake system
+ Body
+ Heating, ventilation
+ Electric equipment

2.7. Inlet collector and laying

GENERAL INFORMATION

Inlet collector

AND. VACUUM HOSE OF THE REGULATOR OF PRESSURE
CENTURY. HOSE OF THE BRAKE AMPLIFIER
PAGE. VACUUM HOSE OF THE RECEIVER OF THE CONDITIONER OF AIR
D. VACUUM HOSE OF THE TANK
Е. THE VACUUM HOSE OF THE SENSOR OF PRESSURE IN THE INLET PIPELINE
F. HOSE OF VENTILATION OF THE CASE
G. BLOWING-OFF HOSE OF THE TANK

53. INLET COLLECTOR
56. BUTTERFLY VALVE CASE

SEQUENCE OF UNSCREWING OF FIXING DETAILS 9–8–7–6–5–4–3–2–1

SEQUENCE OF THE INHALING 1–2–3–4–5–6–7–8–9

To remove or disconnect

PERFORMANCE ORDER

1. Bottom hose of a radiator.

2. To merge cooling liquid.

3. To reject aside the generator.

4. A butterfly valve and a butterfly valve cable from an arm of the inlet pipeline.

5. All vacuum hoses from the case of a butterfly valve and the inlet pipeline.

6. Electric wires from plugs on the butterfly valve case.

7. Fuel pipelines from the butterfly valve case (bringing and drain).

8. A hose of system of cooling from the butterfly valve case.

9. To unscrew the top nuts, then the bottom bolts of fastening of an inlet collector, to remove washers.

10. An inlet collector 53 with laying 52.

11. The interfaced planes of a head of cylinders and an inlet collector.

To establish or attach

PERFORMANCE ORDER

1. An inlet collector 53 with new laying 52.

2. Fixing nuts and bolts with washers to tighten the moment of 22 Nanometers.

3. A hose of system of cooling to the butterfly valve case.

4. Fuel pipelines to the butterfly valve case (bringing and drain).

5. Electric wires to plugs on the butterfly valve case.

6. All vacuum hoses to the case of a butterfly valve and an inlet collector.

7. A butterfly valve and a butterfly valve cable to an arm of an inlet collector.

8. Generator.

9. Bottom hose of a radiator.

10. To fill in cooling liquid.