Daewoo Nexia

since 1994 of release

Repair and car operation


Deu Neksiya
+ Maintenance instruction
+ Maintenance
- Engine
   2.1. Technical characteristics
   2.2. Greasing system
   2.3. Maintenance and engine repair
   2.4. Compression check
   2.5. Dismantle and engine installation assembled
   2.6. Engine support
   2.7. Inlet collector and laying
   2.8. Final collector and laying
   2.9. Cover of the case of a cam-shaft
   2.10. Pulley of a cranked shaft
   2.11. Forward cover of a gear belt
   2.12. Camshaft cogwheel
   2.13. Cogwheel of a cranked shaft
   2.14. Back cover of a gear belt
   2.15. Adjustment of a tension of a gear belt
   2.16. Verification of the angular provision of a camshaft
   2.17. Forward consolidation of a cranked shaft
   2.18. Camshaft. Levers. Hydrojacks of gaps
   2.19. Klapannye of a spring. Consolidations of cores of valves
   2.20. Head of cylinders. Camshaft case
   2.21. Repair of a head of the block of cylinders
   2.22. Dismantle of valves
   2.23. Directing plugs of valves
   2.24. Expansion of openings of plugs
   2.25. Valves
   2.26. Klapannye of a spring
   2.27. Saddles of valves
   2.28. Consolidations of valves
   2.29. Height of a core of the valve concerning a head of the block of cylinders
   + 2.30. Pushers of valves with hydrojacks of gaps
   2.31. Oil pallet
   2.32. A reception branch pipe with the oil filter
   2.33. Oil pump
   2.34. Repair of the oil pump
   2.35. Pistons and rods
   2.36. Flywheel. Back consolidation of a cranked shaft
   2.37. Cranked shaft
   2.38. Rods and radical bearings
   2.39. Replacement of loose leaves
   2.40. Piston group and rods
   2.41. Piston fingers and rings
   2.42. Block of cylinders
   2.43. Installation of pistons
   2.44. Disk balancing with a gear wreath
   2.45. Repair of carving openings
   + 2.46. Diagnostics of malfunctions of the engine
+ 3. Engine (two top camshafts)
+ cooling System
+ Toplevnaya and exhaust systems
+ Electric chain
+ 7. Ignition system
+ 8. Electronic control unit and sensors
+ Transmission
+ 10. Five-speed transmission and main RPO MM5 broadcast
+ 11. Automatic Transmission
+ Steering
+ Running gear
+ 14. Forward suspension bracket
+ 15. Drive of forward wheels
+ 16. Back suspension bracket
+ Brake system
+ Body
+ Heating, ventilation
+ Electric equipment


8128da4b На сайте www.kond-servis.ru обслуживание и ремонт кондиционеров.
Кунжут купить в москве по материалам сайта.


2.36. Flywheel. Back consolidation of a cranked shaft

 To remove or disconnect

PERFORMANCE ORDER
1. Transmission case.
2. Fixing bolts and flywheel 116.
3. A casing of coupling and a conducted disk 115 of coupling (only a hand-operated transmission).
4. To take out back consolidation 117. To clear a landing nest of consolidation in the block and a condensed neck of a shaft.
Prevention

Back consolidation 117 cranked shaft can be replaced without dismantle of the oil pallet or a cranked shaft.


To establish or attach

PERFORMANCE ORDER
1. New back consolidation 117 in a nest of the block of cylinders.
1а. To press consolidation evenly on all perimeter.
1б. For simplification of assembly to grease an external surface of consolidation.
2. A flywheel to tighten bolts the moment of 35 Nanometers, then in addition to wrap bolts on a corner 30 °–45 °.
Prevention

To use only new bolts.

3. A disk 115, a casing of coupling 114 to tighten bolts the moment of 35 Nanometers. Bolts of fastening of a casing of coupling can be used repeatedly.
4. Transmission case.