Deu Neksiya
+ Maintenance instruction
+ Maintenance
+ Engine
- 3. Engine (two top camshafts)
3.2. General description
3.3. Operation of hydraulic jacks of gaps
3.4. Greasing system
3.5. Maintenance and repair
3.6. Compression check
3.7. Dismantle and engine installation assembled
3.8. Maple belt
3.9. Engine support
3.10. Inlet collector and laying
3.11. Final collector and laying
3.12. Cover of the klapanny mechanism and laying
3.13. Pulley of a cranked shaft
3.14. Forward cover of a gear belt
3.15. Gear belt
3.16. Natyazhitel of a gear belt
3.17. Camshaft cogwheel
3.18. Cogwheel of a cranked shaft
3.19. Back cover of a gear belt
3.20. Forward consolidation of a cranked shaft
3.21. Camshaft. Hydrojacks of gaps of valves
3.22. Head of the block of cylinders
3.23. Repair of a head of the block of cylinders
3.24. Klapannye of a spring. Consolidations of cores of valves
3.25. Dismantle of valves
3.26. Directing plugs of valves
3.27. Expansion of openings of plugs
3.28. Valves
3.29. Klapannye of a spring
3.30. Saddles of valves
3.31. Oil pallet
3.32. A reception branch pipe with the oil filter
3.33. Oil pump
3.34. Repair of the oil pump
3.35. Pistons and rods
3.36. Flywheel. Back consolidation of a cranked shaft
3.37. Cranked shaft
3.38. Rods and radical bearings
3.39. Replacement of loose leaves
3.40. Piston fingers and rings
3.41. Block of cylinders
3.42. Installation of pistons
3.43. Disk balancing with a gear wreath
3.44. Repair of carving openings
3.45. Diagnostics of malfunctions
+ cooling System
+ Toplevnaya and exhaust systems
+ Electric chain
+ 7. Ignition system
+ 8. Electronic control unit and sensors
+ Transmission
+ 10. Five-speed transmission and main RPO MM5 broadcast
+ 11. Automatic Transmission
+ Steering
+ Running gear
+ 14. Forward suspension bracket
+ 15. Drive of forward wheels
+ 16. Back suspension bracket
+ Brake system
+ Body
+ Heating, ventilation
+ Electric equipment
|
General characteristics
| Engine type |
Ryadny, 4-cylinder
|
| Working volume |
1498 cubic cm (1,5л)
|
| Diameter of the cylinder |
76,5 mm
|
| Piston stroke |
81,5 mm
|
| Extent of compression |
9,2
|
| Operating procedure of cylinders |
1–3–4–2
|
Cylinders
| Diameter of the cylinder |
76,495-76,505 mm
|
| Admissible ovality |
0,013 mm
|
| Admissible konusnost |
0,013 mm
|
| Admissible konusnost in the plane of rotation of a crank |
0,02 mm
|
Pistons
| Diameter |
76,465-76,475 mm
|
| Gap between the piston and the cylinder |
0,02-0,04 mm
|
Piston rings
| Gaps in the lock: |
| – top kompressionny ring |
0,3-0,5 mm
|
| – bottom kompressionny ring |
0,3-0,5 mm
|
| Ring gap in a flute: |
| – top kompressionny ring |
0,060-0,092 mm
|
| – bottom kompressionny ring |
0,050-0,082 mm
|
Piston fingers
| Diameter |
17,990-17,995 mm
|
| Finger gap in the piston |
0,01-0,02 mm
|
| Finger landing in a rod head |
The dense
|
Camshafts
| Lifting of the inlet valve |
8,5 mm
|
| Lifting of the final valve |
8,5 mm
|
| Axial gap of a shaft |
0,04-0,06 mm
|
| Diameters of necks of a shaft: |
| – the 1st |
29,935-29,950 mm
|
| – 2nd |
26,935-26,950 mm
|
| – 3rd |
26,935-26,950 mm
|
| – 4th |
26,935-26,950 mm
|
| – the 5th |
26,935-26,950 mm
|
| Diameters of openings of bearings: |
| – the 1st |
30,000-30.021 mm
|
| – the 2nd |
27,000-27,021 mm
|
| – the 3rd |
27,000-27,021 mm
|
| – the 4th |
27,000-27,021 mm
|
| – the 5th |
27,000-27,021 mm
|
| Gaps in bearings |
0,050-0,086 mm
|
Cranked shaft
| Radical necks: |
| – diameter |
54,980-54,997 mm
|
| – admissible konusnost |
0,005 mm
|
| – admissible ovality |
0,004 mm
|
| Radical bearings: |
| – gaps |
0,015-0,040 mm
|
| Axial gap of a shaft |
0,070-0,32 mm
|
| Shatunnye of a neck: |
| – diameter |
42,971-42.987 mm
|
| – admissible konusnost |
0,005 mm
|
| – admissible ovality |
0,004 mm
|
| Gaps in shatunny bearings |
0,019-0,063 mm
|
| Lateral gap in a rod the bearing |
0,070-0,242 mm
|
Klapanny mechanism
| Jacks of gaps |
The hydraulic
|
| Corner of a facet of valves (all valves) |
45 °
|
| Corner of a facet of saddles (all saddles) |
45 °
|
| Admissible not coaxiality of a saddle and plug |
0,05 mm
|
| Admissible not coaxiality of a facet of the valve |
0,015 mm
|
| Width of a saddle |
1,2-1,6 mm
|
| Directing plugs: |
| – internal diameter |
6 00 – 6,02 mm
|
| Diameters of cores of valves: |
| – the final |
5,955-5,970 mm
|
| – the inlet |
5,935-5,950 mm
|
| Gaps of valves in plugs: |
| – inlet valve |
0,030-0,065 mm
|
| – final valve |
0,050-0,085 mm
|
| Effort/length of klapanny springs: |
| – at the open valve |
556,5-603,5 N/23 of mm
|
| – at the closed valve |
247-273 N/32 of mm
|
Oil pump
| Lateral gap in gearing of gear wheels |
0,10-0,20 mm
|
| Radial gap of a gear wheel with internal gearing in the case |
0,11-0,19 mm
|
| Radial gap of a gear wheel with internal gearing in interface to a segment |
0,40-0,50 mm
|
| Radial gap of a gear wheel with external gearing in interface to a segment |
0,35-0,40 mm
|
| Face gap |
0,030-0,10 mm
|
| Depth of a nest of gear wheels |
10,03-10,08 mm
|
| Diameter of nests of gear wheels: |
| – with external gearing |
41,00-41,025 mm
|
| – with internal gearing |
82,07-82,15 mm
|
| Diameter of gear wheels: |
| – with external gearing |
40,95-40,975 mm
|
| – with internal gearing |
81,910-81,964 mm
|
Moments of an inhaling of carving connections
| Bolts of a cover of the klapanny mechanism |
8 Nanometers
|
| Bolts of a head of cylinders |
20 Nanometers +65 ° +65 ° +65 °
|
| (after engine test) |
30 ° – 40 °
|
| Nuts of the final pipeline |
22 Nanometers
|
| Nuts of fastening of a dual exhaust pipe |
25 Nanometers
|
| Bolt of a natyazhitel of a belt |
25 Nanometers
|
| Bolt of a cogwheel of a cam-shaft |
60 Nanometers
|
| Bolts of a forward cover of a belt |
8 Nanometers
|
| Bottom bolt of an arm of the inlet pipeline |
40 Nanometers
|
| Top bolts of an arm of the inlet pipeline |
25 Nanometers
|
| Nuts and bolts of the inlet pipeline |
25 Nanometers
|
| Flywheel bolts |
35 Nanometers + 30 °–45 °
|
| Bolts of the oil pallet |
5 Nanometers
|
| Drain oil stopper |
45 Nanometers
|
| Bolt of a pulley of a cranked shaft |
55 Nanometers
|
| Bolt of fastening of the water pump |
8 Nanometers
|
| Bolts of covers of shatunny bearings |
25 Nanometers + 30 °
|
|
|
