Daewoo Nexia

since 1994 of release

Repair and car operation

Deu Neksiya
+ Maintenance instruction
+ Maintenance
+ Engine
- 3. Engine (two top camshafts)
   3.2. General description
   3.3. Operation of hydraulic jacks of gaps
   3.4. Greasing system
   3.5. Maintenance and repair
   3.6. Compression check
   3.7. Dismantle and engine installation assembled
   3.8. Maple belt
   3.9. Engine support
   3.10. Inlet collector and laying
   3.11. Final collector and laying
   3.12. Cover of the klapanny mechanism and laying
   3.13. Pulley of a cranked shaft
   3.14. Forward cover of a gear belt
   3.15. Gear belt
   3.16. Natyazhitel of a gear belt
   3.17. Camshaft cogwheel
   3.18. Cogwheel of a cranked shaft
   3.19. Back cover of a gear belt
   3.20. Forward consolidation of a cranked shaft
   3.21. Camshaft. Hydrojacks of gaps of valves
   3.22. Head of the block of cylinders
   3.23. Repair of a head of the block of cylinders
   3.24. Klapannye of a spring. Consolidations of cores of valves
   3.25. Dismantle of valves
   3.26. Directing plugs of valves
   3.27. Expansion of openings of plugs
   3.28. Valves
   3.29. Klapannye of a spring
   3.30. Saddles of valves
   3.31. Oil pallet
   3.32. A reception branch pipe with the oil filter
   3.33. Oil pump
   3.34. Repair of the oil pump
   3.35. Pistons and rods
   3.36. Flywheel. Back consolidation of a cranked shaft
   3.37. Cranked shaft
   3.38. Rods and radical bearings
   3.39. Replacement of loose leaves
   3.40. Piston fingers and rings
   3.41. Block of cylinders
   3.42. Installation of pistons
   3.43. Disk balancing with a gear wreath
   3.44. Repair of carving openings
   3.45. Diagnostics of malfunctions
+ cooling System
+ Toplevnaya and exhaust systems
+ Electric chain
+ 7. Ignition system
+ 8. Electronic control unit and sensors
+ Transmission
+ 10. Five-speed transmission and main RPO MM5 broadcast
+ 11. Automatic Transmission
+ Steering
+ Running gear
+ 14. Forward suspension bracket
+ 15. Drive of forward wheels
+ 16. Back suspension bracket
+ Brake system
+ Body
+ Heating, ventilation
+ Electric equipment

3.13. Pulley of a cranked shaft

GENERAL INFORMATION

Dismantle of a pulley of the pump of the steering amplifier

Dismantle of a pulley of a cranked shaft

To remove or disconnect

PERFORMANCE ORDER

1. Negative wire of the storage battery.

2. To weaken a tension and to remove a belt of the compressor of the conditioner.

3. To weaken fastening of the generator and to release a driving belt.

4. Holding a key of 9 mm a pulley from rotation, to unscrew bolts In and to remove a pulley And.

5. A forward cover 73 gear belts, having turned out 2 bolts 75.

6. Holding a key of 24 mm a camshaft from rotation, to unscrew a bolt 159, to remove a washer 158 and a pulley 157.

To establish or attach

PERFORMANCE ORDER

1. Holding a key of 24 mm a camshaft from rotation, to wrap a bolt 159, previously having established a washer 158 and a pulley 157.

2. To tighten a bolt of a pulley of a cranked shaft the moment of 155 Nanometers.

3. A forward cover 73 gear belts, having screwed 2 bolts 75.

4. Pulley of the pump of the steering amplifier. Holding a key of 9 mm a pulley from rotation, to screw in three bolts of Century.

5. To establish belts on a pulley of the generator and a compressor pulley.

6. Negative wire of the storage battery.