Daewoo Nexia

since 1994 of release

Repair and car operation

Deu Neksiya
+ Maintenance instruction
+ Maintenance
+ Engine
- 3. Engine (two top camshafts)
   3.2. General description
   3.3. Operation of hydraulic jacks of gaps
   3.4. Greasing system
   3.5. Maintenance and repair
   3.6. Compression check
   3.7. Dismantle and engine installation assembled
   3.8. Maple belt
   3.9. Engine support
   3.10. Inlet collector and laying
   3.11. Final collector and laying
   3.12. Cover of the klapanny mechanism and laying
   3.13. Pulley of a cranked shaft
   3.14. Forward cover of a gear belt
   3.15. Gear belt
   3.16. Natyazhitel of a gear belt
   3.17. Camshaft cogwheel
   3.18. Cogwheel of a cranked shaft
   3.19. Back cover of a gear belt
   3.20. Forward consolidation of a cranked shaft
   3.21. Camshaft. Hydrojacks of gaps of valves
   3.22. Head of the block of cylinders
   3.23. Repair of a head of the block of cylinders
   3.24. Klapannye of a spring. Consolidations of cores of valves
   3.25. Dismantle of valves
   3.26. Directing plugs of valves
   3.27. Expansion of openings of plugs
   3.28. Valves
   3.29. Klapannye of a spring
   3.30. Saddles of valves
   3.31. Oil pallet
   3.32. A reception branch pipe with the oil filter
   3.33. Oil pump
   3.34. Repair of the oil pump
   3.35. Pistons and rods
   3.36. Flywheel. Back consolidation of a cranked shaft
   3.37. Cranked shaft
   3.38. Rods and radical bearings
   3.39. Replacement of loose leaves
   3.40. Piston fingers and rings
   3.41. Block of cylinders
   3.42. Installation of pistons
   3.43. Disk balancing with a gear wreath
   3.44. Repair of carving openings
   3.45. Diagnostics of malfunctions
+ cooling System
+ Toplevnaya and exhaust systems
+ Electric chain
+ 7. Ignition system
+ 8. Electronic control unit and sensors
+ Transmission
+ 10. Five-speed transmission and main RPO MM5 broadcast
+ 11. Automatic Transmission
+ Steering
+ Running gear
+ 14. Forward suspension bracket
+ 15. Drive of forward wheels
+ 16. Back suspension bracket
+ Brake system
+ Body
+ Heating, ventilation
+ Electric equipment

3.9. Engine support

GENERAL INFORMATION

Traverse for engine fastening

Prevention

In order to avoid a travmirovaniye it is necessary to watch closely correctness of installation and reliability of fastening of the engine to technological a traverse (KM-263 adaptation), established over a motor compartment.

Defective support of the engine should be replaced at once new in order to avoid failure of other support and other details.

To check

PERFORMANCE ORDER

1. To raise the Engine, to unload rubber pillows of support.

2. A surface of rubber pillows on existence of cracks because of an overheat.

3. Backlog of rubber pillows from plates.

4. Existence of cracks and ruptures of rubber in the middle of pillows.

5. Weakening of an inhaling of bolts and nuts.

To remove or disconnect

PERFORMANCE ORDER

1. Negative wire of the storage battery.

2. To suspend the Engine on a traverse (KM-263 adaptation).

3. Bolt of an arm of the right forward support.

4. A bolt of fastening of an arm of the right forward support to the engine block.

5. Nuts and washers of the right forward support.

6. Bolts of an arm of the left forward support.

7. Bolts of fastening of an arm of the left forward support to the engine block.

8. Bolts and washers of the left forward support.

9. Nut, bolt, washer and arm of a back support.

10. Bolts, washers and a back support of the engine from the car.