Daewoo Nexia

since 1994 of release

Repair and car operation



Deu Neksiya
+ Maintenance instruction
- Maintenance
   1.2. General instructions on repair
   1.2. Identification number of the car
   1.3. Car lifting
   1.4. Car maintenance
   + 1.5. Control surveys and the servicing, carried out by the owner
   1.6. Moments of an inhaling of carving connections
   1.7. Car characteristics with system of multipoint injection of fuel
   1.8. Characteristics of cars (2 top camshafts of the engine)
   1.9. Sizes and mass of cars
+ Engine
+ 3. Engine (two top camshafts)
+ cooling System
+ Toplevnaya and exhaust systems
+ Electric chain
+ 7. Ignition system
+ 8. Electronic control unit and sensors
+ Transmission
+ 10. Five-speed transmission and main RPO MM5 broadcast
+ 11. Automatic Transmission
+ Steering
+ Running gear
+ 14. Forward suspension bracket
+ 15. Drive of forward wheels
+ 16. Back suspension bracket
+ Brake system
+ Body
+ Heating, ventilation
+ Electric equipment


8128da4b



Maintenance

1. Maintenance

1.1. General information

GENERAL INFORMATION

Basic rules of safety measures

Appropriate Maintenance and repair are very important from the point of view of safe operation and reliability of the car. In this management effective and correct receptions of carrying out all necessary operations on servicing and car repairs are described. In certain cases use of special tools and adaptations is required. These tools and adaptations should be used in strict accordance with recommendations.

At work with the Electric equipment, connected with possibility of short circuit, it is necessary to disconnect a "mass" wire of the storage battery. After connection of the battery it is necessary to establish anew indications of the electric clock, to repeat control and to bring in memory of a radio receiver of frequency of stations of a broadcasting, and also to reprogram other electronic equipment of the car. Stated above caution are not exhaustive. The DEU company cannot, naturally, in advance to provide all possible options of technological operations and dangerous situations which can arise at carrying out repair and car maintenance. Therefore before putting into practice any reception or the tool, excellent that are recommended in this management, it is very important to be convinced of safety for the personnel and the car. In this guide of operation to maintenance and repair are described, generally for cars with a left foreign steering. On cars with a right-hand steering all operations are carried out similarly (in a specular reflection). Functions of various systems and devices of the car do not depend on steering option. In the presence of any essential features of cars with various options of a steering the relevant additional information is provided in the management.

General instructions on repair

When using a floor jack it is necessary to observe the following rules. Put the car on a horizontal platform. Block from possible movings a forward or back wheel. Establish a jack under a basic nest of the Body and lift the car. Substitute under the car safety rigid support. Only after that it is possible to start carrying out servicing or repair.

Before work DISCONNECT the "MASS" WIRE of the storage battery in order to avoid damages of the car and traumas because of short circuit.

Use safety covers for protection of the Body, seats and rugs on a floor from damages and pollution. Do not allow hit of brake liquid and cooling liquid on a car Body as they can damage a paint and varnish covering.

Use only the serviceable tool recommended in this management.

The reuse шплинтов, laying, sealing rings of round section, manzhetny consolidations, lock washers and самоконтрящихся nuts is not allowed. At assembly of units it is necessary to replace them with new details. Otherwise normal operation of units cannot be guaranteed.

For simplification and acceleration of assembly of units accurately store the disassembled details in separate groups.

Do not confuse various fixing bolts and nuts as they differ on durability and design features depending on an installation site.

Clear details of pollution before their survey or installation.

Details of oil systems also are subject to cleaning and a purge the compressed air for removal of all pollution.

Before installation of details grease surfaces of sliding and rotation by liquid oil or konsistentny greasing.

If necessary for elimination of a leak of oil or operational liquids use hermetic together with sealing laying.

Carefully observe requirements to size of the moment of a tightening of bolts and nuts.

After completion of servicing or repair carry out final check to be convinced of the correct performance of all operations and malfunction elimination.