Daewoo Nexia

since 1994 of release

Repair and car operation



Deu Neksiya
+ Maintenance instruction
+ Maintenance
- Engine
   2.1. Technical characteristics
   2.2. Greasing system
   2.3. Maintenance and engine repair
   2.4. Compression check
   2.5. Dismantle and engine installation assembled
   2.6. Engine support
   2.7. Inlet collector and laying
   2.8. Final collector and laying
   2.9. Cover of the case of a cam-shaft
   2.10. Pulley of a cranked shaft
   2.11. Forward cover of a gear belt
   2.12. Camshaft cogwheel
   2.13. Cogwheel of a cranked shaft
   2.14. Back cover of a gear belt
   2.15. Adjustment of a tension of a gear belt
   2.16. Verification of the angular provision of a camshaft
   2.17. Forward consolidation of a cranked shaft
   2.18. Camshaft. Levers. Hydrojacks of gaps
   2.19. Klapannye of a spring. Consolidations of cores of valves
   2.20. Head of cylinders. Camshaft case
   2.21. Repair of a head of the block of cylinders
   2.22. Dismantle of valves
   2.23. Directing plugs of valves
   2.24. Expansion of openings of plugs
   2.25. Valves
   2.26. Klapannye of a spring
   2.27. Saddles of valves
   2.28. Consolidations of valves
   2.29. Height of a core of the valve concerning a head of the block of cylinders
   + 2.30. Pushers of valves with hydrojacks of gaps
   2.31. Oil pallet
   2.32. A reception branch pipe with the oil filter
   2.33. Oil pump
   2.34. Repair of the oil pump
   2.35. Pistons and rods
   2.36. Flywheel. Back consolidation of a cranked shaft
   2.37. Cranked shaft
   2.38. Rods and radical bearings
   2.39. Replacement of loose leaves
   2.40. Piston group and rods
   2.41. Piston fingers and rings
   2.42. Block of cylinders
   2.43. Installation of pistons
   2.44. Disk balancing with a gear wreath
   2.45. Repair of carving openings
   + 2.46. Diagnostics of malfunctions of the engine
+ 3. Engine (two top camshafts)
+ cooling System
+ Toplevnaya and exhaust systems
+ Electric chain
+ 7. Ignition system
+ 8. Electronic control unit and sensors
+ Transmission
+ 10. Five-speed transmission and main RPO MM5 broadcast
+ 11. Automatic Transmission
+ Steering
+ Running gear
+ 14. Forward suspension bracket
+ 15. Drive of forward wheels
+ 16. Back suspension bracket
+ Brake system
+ Body
+ Heating, ventilation
+ Electric equipment


8128da4b



2.40. Piston group and rods

GENERAL INFORMATION

Installation of safety tubes on shatunny bolts

1. To use short pieces of a hose in diameter 3/8 inches as pistons directing at dismantle assembled with rods.

To remove or disconnect

PERFORMANCE ORDER
1. To mark pistons with serial numbers of cylinders in which they were.
2. To mark rods and covers of the bottom heads that at assembly not to mix a detail.
3. To turn a cranked shaft in the provision of the bottom dead point.
4. To clear carbon deposits (deposit) in the top part of cylinders.
Prevention

If on a cylinder mirror in a zone of the top dead point of the piston there is an appreciable fillet, it is necessary to remove it to демонта жа from the piston cylinder assembled with a rod. For this purpose it is necessary to use a shaber. Not to apply bigger efforts in order to avoid breakage of rings and piston damages.


5. Cover of the bottom head of a rod.
6. The piston assembled with a rod. Вытолкнуть piston suitable adaptation.
Prevention

To establish on shatunny bolts safety tubes, not to injure a neck of a cranked shaft, see fig. Installation of safety tubes on shatunny bolts.