Daewoo Nexia

since 1994 of release

Repair and car operation


Deu Neksiya
+ Maintenance instruction
+ Maintenance
- Engine
   2.1. Technical characteristics
   2.2. Greasing system
   2.3. Maintenance and engine repair
   2.4. Compression check
   2.5. Dismantle and engine installation assembled
   2.6. Engine support
   2.7. Inlet collector and laying
   2.8. Final collector and laying
   2.9. Cover of the case of a cam-shaft
   2.10. Pulley of a cranked shaft
   2.11. Forward cover of a gear belt
   2.12. Camshaft cogwheel
   2.13. Cogwheel of a cranked shaft
   2.14. Back cover of a gear belt
   2.15. Adjustment of a tension of a gear belt
   2.16. Verification of the angular provision of a camshaft
   2.17. Forward consolidation of a cranked shaft
   2.18. Camshaft. Levers. Hydrojacks of gaps
   2.19. Klapannye of a spring. Consolidations of cores of valves
   2.20. Head of cylinders. Camshaft case
   2.21. Repair of a head of the block of cylinders
   2.22. Dismantle of valves
   2.23. Directing plugs of valves
   2.24. Expansion of openings of plugs
   2.25. Valves
   2.26. Klapannye of a spring
   2.27. Saddles of valves
   2.28. Consolidations of valves
   2.29. Height of a core of the valve concerning a head of the block of cylinders
   + 2.30. Pushers of valves with hydrojacks of gaps
   2.31. Oil pallet
   2.32. A reception branch pipe with the oil filter
   2.33. Oil pump
   2.34. Repair of the oil pump
   2.35. Pistons and rods
   2.36. Flywheel. Back consolidation of a cranked shaft
   2.37. Cranked shaft
   2.38. Rods and radical bearings
   2.39. Replacement of loose leaves
   2.40. Piston group and rods
   2.41. Piston fingers and rings
   2.42. Block of cylinders
   2.43. Installation of pistons
   2.44. Disk balancing with a gear wreath
   2.45. Repair of carving openings
   + 2.46. Diagnostics of malfunctions of the engine
+ 3. Engine (two top camshafts)
+ cooling System
+ Toplevnaya and exhaust systems
+ Electric chain
+ 7. Ignition system
+ 8. Electronic control unit and sensors
+ Transmission
+ 10. Five-speed transmission and main RPO MM5 broadcast
+ 11. Automatic Transmission
+ Steering
+ Running gear
+ 14. Forward suspension bracket
+ 15. Drive of forward wheels
+ 16. Back suspension bracket
+ Brake system
+ Body
+ Heating, ventilation
+ Electric equipment


8128da4b



2.22. Dismantle of valves

 To disassemble

PERFORMANCE ORDER
To remove valves and klapanny springs.
Prevention

When dismantling the mechanism of a gazoraspredeleniye it is necessary to keep a complete set of details in separate groups and at assembly to establish them strictly on the same places which they occupied before dismantling. Otherwise it will be broken extra earnings of details.

At dismantle of valves it is necessary to protect directing plugs from damages. If the core of the valve became griboobrazny, it is necessary to remove superfluous metal by means of a file or nazhdachny whetstone. It is forbidden to beat out the valve from the plug a hammer or to small beards.


To clear

PERFORMANCE ORDER
Valves from a deposit and resinous deposits. The deposit is deleted with a wire brush, and by resinous deposits – by means of soaking in liquid for carburetor cleaning.
Prevention

In order to avoid a travmirovaniye when using the mechanized brushes it is obligatory to put on goggles. It is necessary to avoid also steam inhalation and contacts to open sites of a body of liquid for carburetor cleaning. Not to scratch cores of valves rough wire brushes.