Daewoo Nexia

since 1994 of release

Repair and car operation



Deu Neksiya
+ Maintenance instruction
+ Maintenance
- Engine
   2.1. Technical characteristics
   2.2. Greasing system
   2.3. Maintenance and engine repair
   2.4. Compression check
   2.5. Dismantle and engine installation assembled
   2.6. Engine support
   2.7. Inlet collector and laying
   2.8. Final collector and laying
   2.9. Cover of the case of a cam-shaft
   2.10. Pulley of a cranked shaft
   2.11. Forward cover of a gear belt
   2.12. Camshaft cogwheel
   2.13. Cogwheel of a cranked shaft
   2.14. Back cover of a gear belt
   2.15. Adjustment of a tension of a gear belt
   2.16. Verification of the angular provision of a camshaft
   2.17. Forward consolidation of a cranked shaft
   2.18. Camshaft. Levers. Hydrojacks of gaps
   2.19. Klapannye of a spring. Consolidations of cores of valves
   2.20. Head of cylinders. Camshaft case
   2.21. Repair of a head of the block of cylinders
   2.22. Dismantle of valves
   2.23. Directing plugs of valves
   2.24. Expansion of openings of plugs
   2.25. Valves
   2.26. Klapannye of a spring
   2.27. Saddles of valves
   2.28. Consolidations of valves
   2.29. Height of a core of the valve concerning a head of the block of cylinders
   + 2.30. Pushers of valves with hydrojacks of gaps
   2.31. Oil pallet
   2.32. A reception branch pipe with the oil filter
   2.33. Oil pump
   2.34. Repair of the oil pump
   2.35. Pistons and rods
   2.36. Flywheel. Back consolidation of a cranked shaft
   2.37. Cranked shaft
   2.38. Rods and radical bearings
   2.39. Replacement of loose leaves
   2.40. Piston group and rods
   2.41. Piston fingers and rings
   2.42. Block of cylinders
   2.43. Installation of pistons
   2.44. Disk balancing with a gear wreath
   2.45. Repair of carving openings
   + 2.46. Diagnostics of malfunctions of the engine
+ 3. Engine (two top camshafts)
+ cooling System
+ Toplevnaya and exhaust systems
+ Electric chain
+ 7. Ignition system
+ 8. Electronic control unit and sensors
+ Transmission
+ 10. Five-speed transmission and main RPO MM5 broadcast
+ 11. Automatic Transmission
+ Steering
+ Running gear
+ 14. Forward suspension bracket
+ 15. Drive of forward wheels
+ 16. Back suspension bracket
+ Brake system
+ Body
+ Heating, ventilation
+ Electric equipment


8128da4b Ремонт детского квадроцикла.
Регулярные Семена марихуаны, mandala.



2.4. Compression check

GENERAL INFORMATION

Prevention

To disconnect the VAT plug from the ignition or distributor block.


The compression in cylinders of the engine is checked for definition of a technical condition of piston rings and density of a prileganiye of valves to saddles. A compression check at the opened throttle and air zaslonka, the turned-out spark plugs and well charged storage battery. The compression in separate cylinders should not differ strongly. The smallest pressure in cylinders should be not lower than 689 kPas and make not less than 70 % from the maximum value for all cylinders. On each cylinder make measurements during four steps of compression.

Normal state of piston rings and valves

Pressure in cylinders accrues quickly and evenly to nominal rate.

Wear of piston rings

On the first step of compression pressure low, on the subsequent steps pressure increases, but does not reach nominal rate. At the gulf in cylinders of engine oil (on 20–25 ml) the compression considerably increases.

Leaky prileganiye of valves to saddles

On the first and subsequent steps of compression pressure remains low. At the gulf in cylinders of engine oil the compression essentially does not improve. For the gulf in cylinders it is necessary to use the piston supercharger.