Daewoo Nexia

since 1994 of release

Repair and car operation

Deu Neksiya
+ Maintenance instruction
+ Maintenance
- Engine
   2.1. Technical characteristics
   2.2. Greasing system
   2.3. Maintenance and engine repair
   2.4. Compression check
   2.5. Dismantle and engine installation assembled
   2.6. Engine support
   2.7. Inlet collector and laying
   2.8. Final collector and laying
   2.9. Cover of the case of a cam-shaft
   2.10. Pulley of a cranked shaft
   2.11. Forward cover of a gear belt
   2.12. Camshaft cogwheel
   2.13. Cogwheel of a cranked shaft
   2.14. Back cover of a gear belt
   2.15. Adjustment of a tension of a gear belt
   2.16. Verification of the angular provision of a camshaft
   2.17. Forward consolidation of a cranked shaft
   2.18. Camshaft. Levers. Hydrojacks of gaps
   2.19. Klapannye of a spring. Consolidations of cores of valves
   2.20. Head of cylinders. Camshaft case
   2.21. Repair of a head of the block of cylinders
   2.22. Dismantle of valves
   2.23. Directing plugs of valves
   2.24. Expansion of openings of plugs
   2.25. Valves
   2.26. Klapannye of a spring
   2.27. Saddles of valves
   2.28. Consolidations of valves
   2.29. Height of a core of the valve concerning a head of the block of cylinders
   + 2.30. Pushers of valves with hydrojacks of gaps
   2.31. Oil pallet
   2.32. A reception branch pipe with the oil filter
   2.33. Oil pump
   2.34. Repair of the oil pump
   2.35. Pistons and rods
   2.36. Flywheel. Back consolidation of a cranked shaft
   2.37. Cranked shaft
   2.38. Rods and radical bearings
   2.39. Replacement of loose leaves
   2.40. Piston group and rods
   2.41. Piston fingers and rings
   2.42. Block of cylinders
   2.43. Installation of pistons
   2.44. Disk balancing with a gear wreath
   2.45. Repair of carving openings
   + 2.46. Diagnostics of malfunctions of the engine
+ 3. Engine (two top camshafts)
+ cooling System
+ Toplevnaya and exhaust systems
+ Electric chain
+ 7. Ignition system
+ 8. Electronic control unit and sensors
+ Transmission
+ 10. Five-speed transmission and main RPO MM5 broadcast
+ 11. Automatic Transmission
+ Steering
+ Running gear
+ 14. Forward suspension bracket
+ 15. Drive of forward wheels
+ 16. Back suspension bracket
+ Brake system
+ Body
+ Heating, ventilation
+ Electric equipment


2.45. Repair of carving openings


Repair of carving openings



In order to avoid a travmirovaniye of eyes to use goggles.

Defective carving openings can be repaired by a way of a rassverlivaniye, a narezaniye of a carving of bigger diameter and installation of screw carving plugs.

1. To measure diameter, a step and depth of a carving in the damaged opening. If necessary it is necessary to use the restrictive rings established on cutting tool (a drill, a tap). The height of rings is defined by depth of a processed opening.

To specify the demanded diameter of a drill and the sizes of a tap according to the instruction enclosed by the manufacturer of a repair kit.

2. Рассверлить an opening with a defective carving. To remove shavings and agnails.
3. To cut a carving. Previously to grease a tap with engine oil (except a case of a narezaniye of a carving in the aluminum block of cylinders). To clean a carving.

In order to avoid an opening zabivaniye shaving follows periodically (through some working turns) to unscrew and clear a tap.

4. To screw the carving plug on an opravka of the assembly adaptation, fig. Repair of carving openings. To enter into gearing a plug tip with an opravka.
5. To grease an external carving of the plug with engine oil (except a case of installation of the plug in the aluminum block) and to screw in in an opening.

At the correct installation the plug should be drowned on one turn of rather privalochny plane.

6. If the tip of the plug did not break off at an opravka vyvertyvaniye, to remove it with the help a small beard.