Daewoo Nexia

since 1994 of release

Repair and car operation

Deu Neksiya
+ Maintenance instruction
+ Maintenance
+ Engine
+ 3. Engine (two top camshafts)
+ cooling System
+ Toplevnaya and exhaust systems
+ Electric chain
+ 7. Ignition system
+ 8. Electronic control unit and sensors
+ Transmission
+ 10. Five-speed transmission and main RPO MM5 broadcast
+ 11. Automatic Transmission
- Steering
   12.2. General description
   12.3. Reechny steering mechanism assembled
   12.4. Tips of steering drafts
   12.5. Steering drafts
   12.6. Casing of a case of the steering mechanism
   12.7. Coupling of a steering shaft
   12.8. Sealing cover of an opening of a forward board of the Body
   12.9. Plunzher of a lath
   12.10. Shaft gear wheel
   12.11. Lath
   12.12. Needle bearing
   12.13. The directing plug of a lath
   12.14. Verification of the neutral provision of a lath
   12.15. Recommendations about replacement of consolidations in the hydraulic booster
   12.16. Check of level and having added working liquid
   12.17. Air removal from hydrosystem
   12.18. The steering mechanism with the hydraulic booster assembled
   12.19. Hoses and pipelines
   12.20. Tank
   12.21. Tips of steering drafts
   12.22. Steering drafts
   12.23. Plugs of hinges of steering drafts
   12.24. Coupling of a steering shaft
   12.25. Sealing cover
   12.26. Hydrocylinder pipelines
   12.27. Adjustment of a preliminary tightness of a spring of a plunzher
   12.28. Consolidations of a shaft of the hydrodistributor and top bearing
   12.29. Steering mechanism
   12.30. Verification of the neutral provision of a lath
   12.31. Belt of a drive of the pump
   12.32. Pulley of a drive of the pump
   12.33. Pump assembled
   12.34. Control levers on a steering column
   12.35. Steering wheel
   12.36. Ignition lock
   12.37. Steering column
   12.38. Lever switch, steering shaft, steering column (noncontrollable)
   12.39. Lever switch, steering shaft, steering column (adjustable)
+ Running gear
+ 14. Forward suspension bracket
+ 15. Drive of forward wheels
+ 16. Back suspension bracket
+ Brake system
+ Body
+ Heating, ventilation
+ Electric equipment

12.9. Plunzher of a lath

GENERAL INFORMATION

Plunzherny knot of a lath

AND. BEFORE ASSEMBLY TO PUT THE LAYER OF LITHIUM GREASING

40. PLUNZHER
41. SEALING RING
42. SPRING
43. ADJUSTING STOPPER
44. LOCK-NUT

Check of size of the moment of a friction of the steering mechanism

AND. TIP IN THE SIZE 15 MM

5. SHAFT GEAR WHEEL
44. LOCK-NUT

To remove or disconnect

PERFORMANCE ORDER

1. To unscrew a lock-nut 44.

2. To unscrew an adjusting stopper 43.

3. To take out a spring 42.

4. Sealing ring 41.

5. Plunzher 40.

To establish or attach

PERFORMANCE ORDER

1. Plunzher 40.

2. Sealing ring 41.

3. Spring 42.

4. To screw an adjusting stopper 43.

5. To wrap a lock-nut 44.

6. To establish a lath in average situation to tighten an adjusting stopper the moment of 11 Nanometers. Then to unscrew a stopper 43 on 50–70 degrees. To check the friction moment on a shaft gear wheel which should be equal 1,2 Nanometers.

7. To screw a lock-nut 44 and to tighten it for fixing of an adjusting stopper 43.

8. To tighten a lock-nut of an adjusting stopper the moment of 70 Nanometers.