Daewoo Nexia

since 1994 of release

Repair and car operation

Deu Neksiya
+ Maintenance instruction
+ Maintenance
+ Engine
+ 3. Engine (two top camshafts)
+ cooling System
+ Toplevnaya and exhaust systems
+ Electric chain
+ 7. Ignition system
+ 8. Electronic control unit and sensors
+ Transmission
+ 10. Five-speed transmission and main RPO MM5 broadcast
+ 11. Automatic Transmission
- Steering
   12.2. General description
   12.3. Reechny steering mechanism assembled
   12.4. Tips of steering drafts
   12.5. Steering drafts
   12.6. Casing of a case of the steering mechanism
   12.7. Coupling of a steering shaft
   12.8. Sealing cover of an opening of a forward board of the Body
   12.9. Plunzher of a lath
   12.10. Shaft gear wheel
   12.11. Lath
   12.12. Needle bearing
   12.13. The directing plug of a lath
   12.14. Verification of the neutral provision of a lath
   12.15. Recommendations about replacement of consolidations in the hydraulic booster
   12.16. Check of level and having added working liquid
   12.17. Air removal from hydrosystem
   12.18. The steering mechanism with the hydraulic booster assembled
   12.19. Hoses and pipelines
   12.20. Tank
   12.21. Tips of steering drafts
   12.22. Steering drafts
   12.23. Plugs of hinges of steering drafts
   12.24. Coupling of a steering shaft
   12.25. Sealing cover
   12.26. Hydrocylinder pipelines
   12.27. Adjustment of a preliminary tightness of a spring of a plunzher
   12.28. Consolidations of a shaft of the hydrodistributor and top bearing
   12.29. Steering mechanism
   12.30. Verification of the neutral provision of a lath
   12.31. Belt of a drive of the pump
   12.32. Pulley of a drive of the pump
   12.33. Pump assembled
   12.34. Control levers on a steering column
   12.35. Steering wheel
   12.36. Ignition lock
   12.37. Steering column
   12.38. Lever switch, steering shaft, steering column (noncontrollable)
   12.39. Lever switch, steering shaft, steering column (adjustable)
+ Running gear
+ 14. Forward suspension bracket
+ 15. Drive of forward wheels
+ 16. Back suspension bracket
+ Brake system
+ Body
+ Heating, ventilation
+ Electric equipment

12.38. Lever switch, steering shaft, steering column (noncontrollable)

GENERAL INFORMATION

Steering column – standard execution for cars with automatic transmission and a hand-operated transmission

1. NUT
2. SPRING
3. PERSISTENT WASHER
4. SCREW
5. THE CASE FOR FASTENING OF LEVER SWITCHES
6. SREZNA BOLT
7. SREZNA BOLT

8. WASHER
9. TOP CASE OF THE STEERING COLUMN
10. CASING OF THE STEERING COLUMN
11. THE DIRECTING PLUG
12. THE CASE FOR FASTENING OF THE LOCK OF IGNITION
13. ADJUSTING SCREW
14. SWITCH OF THE LOCK OF IGNITION
15. STEERING SHAFT

To remove or disconnect

Dismantle of a srezny bolt

7. SREZNA BOLT
9. TOP CASE OF THE STEERING COLUMN
12. THE CASE FOR FASTENING OF THE LOCK OF IGNITION

PERFORMANCE ORDER

1. Steering wheel.

2. Steering column assembled.

3. Directing plug 11 of the bottom end of a steering shaft 15 if it was not dismantled earlier).

4. A spring 2 since the top end of a steering shaft 15.

5. Persistent washer 3.

6. Screws 4.

7. To turn the case 5 lever switches.

8. To turn the lock cylinder in the situation "RUN" (ignition is switched off).

9. To take out a steering shaft 15 through the bottom opening of a casing 10.

10. Sreznye bolts 7, washers 8 and case of fastening of the lock of ignition.

10а. To drill heads of srezny bolts 7 to steel washers 8. To use a drill in diameter of 6.5 mm, see fig. Dismantle of a srezny bolt.

10б. To remove washers 8, to disconnect the case 12 from the top case 9 of a steering column.

10в. To turn out cores of bolts 7 of the case 12 by means of flat-nose pliers.

Prevention

After operation of drilling of heads of bolts it is necessary to clear details of shaving.

11. The cylinder of the lock of ignition from the case 12.

12. To turn out the adjusting screw 13.

13. Switch of ignition 14 assembled.

14. Sreznye bolts 6 and top case of a steering column.

14а. To drill heads of srezny bolts 6 by means of drill 8-mm.

14б. To disconnect the top case 9 from a flange of a casing the 10th helmsman of a column.

14в. To turn out cores of bolts 6 of the case 9 by means of flat-nose pliers.

Prevention

After operation of drilling of heads of bolts it is necessary to clear details of shaving.

To establish or attach

Installation of the switch of ignition

12. THE CASE FOR FASTENING OF THE LOCK OF IGNITION
13. ADJUSTING SCREW
14. SWITCH OF THE LOCK OF IGNITION

Prevention

All fixing details used in operations described below, should be densely wrapped before a final inhaling the moment of the demanded size.

PERFORMANCE ORDER

1. To connect the top case 9 to a flange of a casing 10 by means of srezny bolts 6. To tighten bolts and to cut off heads, having put a torque about 15 Nanometers.

Prevention

To provide at installation coincidence of a uvula of the cylinder of the lock and a groove of the switch of ignition 14, it is necessary to turn previously them in the situation "RUN".

2. The switch of ignition 14 in the case 12. To be convinced that the pin entered into an opening of an eye of the switch 14.

3. To screw the adjusting screw 13 and to tighten it by hand (the moment about 0,3 Nanometers).

4. The cylinder of the lock of ignition in the case 12.

5. To attach the case 12 to the top case 9 of a steering column by means of washers of 8 and srezny bolts 7. To tighten bolts and to cut off heads, having put a torque about 11 Nanometers.

6. To turn the cylinder of the lock of ignition in the situation "RUN".

7. A steering shaft 15 in a casing 10 through the bottom opening. To advance a shaft against the stop.

8. To turn the cylinder of the lock of ignition in the situation "OFF-LOCK" and to take out a key.

9. To turn a steering shaft 15 before operation of the lock of blocking.

10. The case of 5 lever switches on the top case 9 of a column. To screw screws 4 and to tighten them the moment of 3,4 Nanometers.

11. Directing plug 11 for the bottom end of a steering shaft 15 and in a casing 10.

12. A steering column assembled on the car.

Prevention

After connection of a steering shaft with a shaft of the steering mechanism to take out directing plug 11 of a casing 10 and to leave it on the helmsman to a shaft 15 for use further.

13. A persistent washer 3 and a spring for the top end of a shaft 15.

14. A steering wheel on a shaft 15. To screw a nut 1 and to tighten it the moment of 17 Nanometers.