Deu Neksiya
+ Maintenance instruction
+ Maintenance
+ Engine
+ 3. Engine (two top camshafts)
+ cooling System
+ Toplevnaya and exhaust systems
+ Electric chain
+ 7. Ignition system
+ 8. Electronic control unit and sensors
+ Transmission
+ 10. Five-speed transmission and main RPO MM5 broadcast
+ 11. Automatic Transmission
- Steering
12.2. General description
12.3. Reechny steering mechanism assembled
12.4. Tips of steering drafts
12.5. Steering drafts
12.6. Casing of a case of the steering mechanism
12.7. Coupling of a steering shaft
12.8. Sealing cover of an opening of a forward board of the Body
12.9. Plunzher of a lath
12.10. Shaft gear wheel
12.11. Lath
12.12. Needle bearing
12.13. The directing plug of a lath
12.14. Verification of the neutral provision of a lath
12.15. Recommendations about replacement of consolidations in the hydraulic booster
12.16. Check of level and having added working liquid
12.17. Air removal from hydrosystem
12.18. The steering mechanism with the hydraulic booster assembled
12.19. Hoses and pipelines
12.20. Tank
12.21. Tips of steering drafts
12.22. Steering drafts
12.23. Plugs of hinges of steering drafts
12.24. Coupling of a steering shaft
12.25. Sealing cover
12.26. Hydrocylinder pipelines
12.27. Adjustment of a preliminary tightness of a spring of a plunzher
12.28. Consolidations of a shaft of the hydrodistributor and top bearing
12.29. Steering mechanism
12.30. Verification of the neutral provision of a lath
12.31. Belt of a drive of the pump
12.32. Pulley of a drive of the pump
12.33. Pump assembled
12.34. Control levers on a steering column
12.35. Steering wheel
12.36. Ignition lock
12.37. Steering column
12.38. Lever switch, steering shaft, steering column (noncontrollable)
12.39. Lever switch, steering shaft, steering column (adjustable)
+ Running gear
+ 14. Forward suspension bracket
+ 15. Drive of forward wheels
+ 16. Back suspension bracket
+ Brake system
+ Body
+ Heating, ventilation
+ Electric equipment
|
To remove or disconnect
| PERFORMANCE ORDER |
| 1. Fixing plate 37 from heads of bolts 38. A plate to throw out. |
| 2. Bolt of the 38th fastening of the internal hinge of steering draft. If one steering draft is dismantled, to deduce a head of this draft from space between a basic plate 39 and a washer 29 and to remove draft. At simultaneous dismounting of both steering drafts it is necessary to screw after removal of the first draft into place a bolt 38 to keep the mutual provision of a lath, a casing 44 and a directing level. |
| 3. To weaken a coupling bolt. |
| 4. To remove steering draft. |
|
To establish or attach
Installation of steering drafts
|
|
AND. THE ARRANGEMENT OF CUTS OF THE PLATE AT INSTALLATION
29. WASHER
35. STEERING DRAUGHT (LEFT)
37. THE FIXING PLATE
38. BOLT
39. BASIC PLATE
40. STEERING DRAUGHT (RIGHT)
44. CASE CASING |
| PERFORMANCE ORDER |
| 1. To screw in draft the adjusting screw. To tighten a bolt of klemmovy connection of steering draft the moment of 22 Nanometers. |
| 2. To insert into deepenings of a casing 44 and to center concerning openings of a washer 29. |
| 3. To insert bolts 38 into openings of a basic plate, further – in plugs of 36 hinges of steering drafts 35 and 40, in openings of washers 29 and a directing level 28 which is in a casing 44. To screw bolts 38 in a lath of the steering mechanism. To tighten bolts of fastening of steering bent for to a lath of the steering mechanism the moment of 90 Nanometers. |
| 4. To establish on heads of bolts 38 new fixing plate 37. To pay attention to the correct arrangement of cuts of a plate. |
|
|
|
