Deu Neksiya
+ Maintenance instruction
+ Maintenance
+ Engine
+ 3. Engine (two top camshafts)
+ cooling System
+ Toplevnaya and exhaust systems
+ Electric chain
+ 7. Ignition system
+ 8. Electronic control unit and sensors
+ Transmission
+ 10. Five-speed transmission and main RPO MM5 broadcast
+ 11. Automatic Transmission
- Steering
12.2. General description
12.3. Reechny steering mechanism assembled
12.4. Tips of steering drafts
12.5. Steering drafts
12.6. Casing of a case of the steering mechanism
12.7. Coupling of a steering shaft
12.8. Sealing cover of an opening of a forward board of the Body
12.9. Plunzher of a lath
12.10. Shaft gear wheel
12.11. Lath
12.12. Needle bearing
12.13. The directing plug of a lath
12.14. Verification of the neutral provision of a lath
12.15. Recommendations about replacement of consolidations in the hydraulic booster
12.16. Check of level and having added working liquid
12.17. Air removal from hydrosystem
12.18. The steering mechanism with the hydraulic booster assembled
12.19. Hoses and pipelines
12.20. Tank
12.21. Tips of steering drafts
12.22. Steering drafts
12.23. Plugs of hinges of steering drafts
12.24. Coupling of a steering shaft
12.25. Sealing cover
12.26. Hydrocylinder pipelines
12.27. Adjustment of a preliminary tightness of a spring of a plunzher
12.28. Consolidations of a shaft of the hydrodistributor and top bearing
12.29. Steering mechanism
12.30. Verification of the neutral provision of a lath
12.31. Belt of a drive of the pump
12.32. Pulley of a drive of the pump
12.33. Pump assembled
12.34. Control levers on a steering column
12.35. Steering wheel
12.36. Ignition lock
12.37. Steering column
12.38. Lever switch, steering shaft, steering column (noncontrollable)
12.39. Lever switch, steering shaft, steering column (adjustable)
+ Running gear
+ 14. Forward suspension bracket
+ 15. Drive of forward wheels
+ 16. Back suspension bracket
+ Brake system
+ Body
+ Heating, ventilation
+ Electric equipment
|
Steering column with an adjustable tilt angle of a steering wheel for cars with automatic transmission and a hand-operated transmission
1. NUT
2. SPRING OF THE MECHANISM OF SWITCHING OFF OF INDEXES OF TURN
3. SPRING RING
4. HOLDER
5. SPRING OF THE TOP BEARING
6. SCREW
7. THE CASE FOR FASTENING OF LEVER SWITCHES
8. SADDLE
9. INTERNAL RING
10. SREZNA BOLT
11. WASHER
12. ROTARY CASE OF THE COLUMN |
13. AXIS OF THE ROTARY CASE
14. THE CASE FOR FASTENING OF THE LOCK OF IGNITION
15. SWITCH OF THE LOCK OF IGNITION
16. ADJUSTING SCREW
17. SPRING OF THE MECHANISM OF CHANGE OF THE TILT ANGLE OF THE STEERING WHEEL
18. HOLDER OF THE SPRING
19. SHARNIRNY STEERING SHAFT ASSEMBLED
20. TOP STEERING SHAFT
21. HEMISPHERICAL CRACKER
22. SPRING
23. BOTTOM STEERING SHAFT
24. EMPHASIS OF THE ROTARY CASE
25. BOLT
26. SUPPORT OF THE STEERING COLUMN
27. CASING OF THE STEERING COLUMN |
To remove or disconnect
Dismantle and installation of a spring ring
|
|
3. SPRING RING
20. TOP PART OF THE STEERING SHAFT |
Dismantle of axes of the rotary case of a steering column
|
|
12. ROTARY CASE OF THE COLUMN
13. AXIS OF THE ROTARY CASE |
| PERFORMANCE ORDER |
| 1. Steering wheel. |
| 2. Steering column assembled. |
| 3. Directing plug 28 of the bottom end of a steering shaft 19 (if it was not dismantled earlier). |
| 4. A spring 2 since the top end of a shaft 19 (if it was not dismantled earlier). |
| 5. Screws 6. |
| 6. Case of 7 lever switches. |
| 7. To compress a spring 5 through the holder 4. |
| 8. Spring ring 3, holder 4, spring 5, saddle 8 and internal ring 9. |
| 9. To pull for the lever of an inclination of the column, located on the case 12, and to lift a steering wheel up against the stop. |
| 10. To insert a krestovy screw-driver into a square opening of the holder of the 18th spring, to press down and, having turned a screw-driver counter-clockwise, to release the holder 18 and a spring 17. |
| 11. Holder 18 and spring 17. |
| 12. Two axes 13. |
| 13. To turn the lock cylinder in the situation "RUN" (Ignition is included). |
| 14. To pull the lever of adjustment of an inclination of a steering wheel and to take out the rotary case 12 of a support the 26th helmsman of a column. |
| 15. Sreznye bolts 10, washers 11 and to disconnect the case 14 of fastening of the lock of ignition from the rotary case 12. |
| 15а. To drill heads of srezny bolts 10 to steel washers 11. To use a drill in diameter of 6,5 mm, see fig. Initial and final provisions of a shaft gear wheel. |
| 15б. To remove washers 11, to disconnect the case 14 from the rotary case 12 of a steering column. |
15в. To turn out cores of bolts 10 of the case 14 by means of flat-nose pliers.
Prevention
After operation высверлива a niya of heads of bolts it is necessary to clear details of shaving.
|
| 16. The cylinder of the lock of ignition from the case 14. |
| 17. To turn out the adjusting screw 16. |
| 18. Switch of ignition 15 assembled. |
| 19. To take out a steering shaft 19 assembled through an opening of a support 26. |
| 20. An emphasis 24 by means of flat-nose pliers. |
| 21. Bolts 25 and to disconnect a support 26 from a flange of a casing the 27th helmsman of a column. |
|
To disassemble
Dismantling and assembly of the hinge of a steering shaft
|
|
20. TOP STEERING SHAFT
21. HEMISPHERICAL CRACKER
22. SPRING
23. BOTTOM STEERING SHAFT |
If necessary repair of a sharnirny steering shaft 19 is carried out as follows.
Prevention
Before disconnecting from each other top 20 and the bottom 23 parts of a steering shaft, it is necessary to notice a relative positioning of a longitudinal flute on a shaft 20 and лыски under a coupling bolt on a shaft 23. If to turn a steering shaft 19 so that the flute under a uvula of blocking of a steering shaft settled down from above (the hour hand is at 12 o'clock), situation лыски should correspond to the hour hand indicating at 7 o'clock. At assembly of a detail of a steering shaft should be established in the same situation.
| PERFORMANCE ORDER |
| 1. To turn a steering shaft 20 on 90 degrees of rather bottom shaft 23 and to disconnect the last from the hinge, see fig. Dismantle of axes of the rotary case of a steering column. |
| 2. To turn a spherical cracker on 90 degrees and to take out it from a fork of a shaft 20. |
| 3. To separate hemispherical crackers 21 and to remove previously the loaded spring 22. |
|
To collect
Correct mutual provision of the top and bottom steering shaft
|
20. TOP STEERING SHAFT
|
23. BOTTOM STEERING SHAFT
|
| PERFORMANCE ORDER |
| 1. To grease hemispherical crackers 21 and a spring with the 22nd konsistentny lithium greasing. |
| 2. To establish a spring 22 between hemispherical crackers 21, having inserted the spring ends into the corresponding grooves of crackers, see fig. Dismantle of axes of the rotary case of a steering column. |
| 3. To grease a fork of the top shaft with the 20th konsistentny lithium greasing. |
| 4. To insert crackers 21 assembled into a fork of a shaft 20 and to develop them on 90 degrees. |
5. To grease a fork of the bottom shaft with the 23rd konsistentny lithium greasing.
Prevention
For the correct assembly top 20 and the bottom 23 steering shaft to execute the following. To turn the top shaft 20 so that the flute under a uvula of blocking of a steering shaft settled down from above (an hour hand at 12 o'clock). Lyska on the end of the bottom shaft 23 should settle down from below at the left (an hour hand at 7th o'clock), see fig. Correct mutual provision of the top and bottom steering shaft.
|
| 6. To develop the top shaft 20 on 90 degrees of rather bottom shaft 23. |
| 7. To insert a fork of a shaft 23 into the hinge and to straighten a steering shaft assembled. |
|
To establish or attach
Prevention
All fixing details used in assembly operations described below, should be densely wrapped before a final inhaling the moment of the demanded size.
| PERFORMANCE ORDER |
| 1. A support 26 to a flange of a casing 27 by means of bolts 25. To tighten bolts the moment of 16 Nanometers. |
| 2. An emphasis 24 about a support 26 and a spring ring into place. |
| 3. To insert a steering shaft 19 into an opening of a support 26. |
| 4. To grease both bearings of the rotary case 12 of a column with konsistentny lithium greasing. |
| 5. To establish the case 12 on a shaft 19 and in a support 26. |
| 6. To grease axes 13 with konsistentny lithium greasing |
7. To insert axes 13 into case 12 openings against the stop.
Prevention
After installation it is necessary закернить for an axis 13 in the case 12. Кернить each axis in three places which have been evenly located on a circles.
|
| 8. To pull for the mechanism lever регулиро vaniye of a tilt angle of a steering wheel and to lift a steering wheel most up. |
| 9. To grease a spring of the 17th mechanism of adjustment of a tilt angle of a steering wheel with konsistentny lithium greasing. |
10. Spring 17 and holder 18. To be convinced that the end of a spring 17 is put on a hook of a support 26. To insert a krestovy screw-driver into a square opening of the holder of the 18th spring, to press down and having turned a screw-driver clockwise, to fix the holder 18.
Prevention
To provide at installation coincidence of a uvula of the cylinder of the lock and a groove of the switch of ignition 15, it is necessary to turn previously them in the situation "RUN".
|
| 11. The switch of ignition 15 in the case 14. To be convinced that the pin entered into an opening of an eye of the switch 15. |
| 12. To screw the adjusting screw 16 and to tighten it by hand (the moment about 0,3 Nanometers). |
| 13. The cylinder of the lock of ignition about the case 14. |
| 14. To attach the case 14 to the rotary case 12 of a steering column by means of washers of 11 and srezny bolts 10. To tighten bolts and to cut off heads, having put a torque about 11 Nanometers. |
| 15. To turn the cylinder of the lock of ignition the situation "OFF-LOCK" and to take out a key. |
| 16. To turn a steering shaft 19 before operation of the lock of blocking. |
| 17. Internal ring 9, saddle 8, spring 5 top bearings and holder 4. |
| 18. To press on the holder 4 and to compress a spring 5, see fig. Dismantle and installation of a spring ring. |
| 19. A spring ring 3 in a flute on the top helmsman to a shaft 20. |
| 20. The case of 7 lever switches on the rotary case 12. To screw screws 6 and to tighten them the moment of 3,4 Nanometers. |
| 21. Directing plug 28 for the bottom end of a steering shaft 23 and in a nest of a casing 27. |
22. A steering column assembled on the car.
Prevention
After connection of a steering shaft with a shaft of the steering mechanism to take out directing plug 28 of a casing 27 and to leave it on the helmsman to a shaft 19 for use further.
|
| 23. A spring of 21 mechanisms of switching off of indexes of turn and a steering wheel on a shaft. |
| 24. To screw a nut 1 and to tighten it the moment of 17 Nanometers. |
|
|
|
