Daewoo Nexia

since 1994 of release

Repair and car operation

Deu Neksiya
+ Maintenance instruction
+ Maintenance
+ Engine
+ 3. Engine (two top camshafts)
+ cooling System
+ Toplevnaya and exhaust systems
+ Electric chain
+ 7. Ignition system
+ 8. Electronic control unit and sensors
+ Transmission
+ 10. Five-speed transmission and main RPO MM5 broadcast
+ 11. Automatic Transmission
- Steering
   12.2. General description
   12.3. Reechny steering mechanism assembled
   12.4. Tips of steering drafts
   12.5. Steering drafts
   12.6. Casing of a case of the steering mechanism
   12.7. Coupling of a steering shaft
   12.8. Sealing cover of an opening of a forward board of the Body
   12.9. Plunzher of a lath
   12.10. Shaft gear wheel
   12.11. Lath
   12.12. Needle bearing
   12.13. The directing plug of a lath
   12.14. Verification of the neutral provision of a lath
   12.15. Recommendations about replacement of consolidations in the hydraulic booster
   12.16. Check of level and having added working liquid
   12.17. Air removal from hydrosystem
   12.18. The steering mechanism with the hydraulic booster assembled
   12.19. Hoses and pipelines
   12.20. Tank
   12.21. Tips of steering drafts
   12.22. Steering drafts
   12.23. Plugs of hinges of steering drafts
   12.24. Coupling of a steering shaft
   12.25. Sealing cover
   12.26. Hydrocylinder pipelines
   12.27. Adjustment of a preliminary tightness of a spring of a plunzher
   12.28. Consolidations of a shaft of the hydrodistributor and top bearing
   12.29. Steering mechanism
   12.30. Verification of the neutral provision of a lath
   12.31. Belt of a drive of the pump
   12.32. Pulley of a drive of the pump
   12.33. Pump assembled
   12.34. Control levers on a steering column
   12.35. Steering wheel
   12.36. Ignition lock
   12.37. Steering column
   12.38. Lever switch, steering shaft, steering column (noncontrollable)
   12.39. Lever switch, steering shaft, steering column (adjustable)
+ Running gear
+ 14. Forward suspension bracket
+ 15. Drive of forward wheels
+ 16. Back suspension bracket
+ Brake system
+ Body
+ Heating, ventilation
+ Electric equipment

12.3. Reechny steering mechanism assembled

GENERAL INFORMATION

Reechny steering mechanism

1. COUPLING BOLT OF THE COUPLING
2. COUPLING
3. SEALING COVER of the OPENING of the FORWARD BOARD of the Body
4. CONSOLIDATION VALA-SHESTERNI
5. VAL-SHESTERNYA ASSEMBLED
6. NEEDLE BEARING
7. CASE OF THE STEERING MECHANISM
8. CASE CAP (LEFT)
9. RUBBER ASSEMBLY PLUG
10. THE DIRECTING LEVEL OF THE LATH
11. SPRING RING
12. IT IS NOT USED
13. THE BOLT (ONLY FOR CARS WITH AUTOMATIC TRANSMISSION)
14. THE COLLAR (ONLY FOR CARS WITH AUTOMATIC TRANSMISSION)
15. THE NUT (ONLY FOR CARS WITH AUTOMATIC TRANSMISSION)
16. CASING PLUG
17. CASING COLLAR
18. ADJUSTING SCREW
19. TIP OF STEERING DRAUGHT (LEFT)
20. SEALING COVER
21. NUT
22. COUPLING BOLT

23. STEERING DRAUGHT (LEFT)
24. THE FIXING PLATE
25. BOLT
26. THE BASIC PLATE (ONLY FOR CARS WITH THE MANUAL TRANSMISSION)
27. SHARNIPA PLUG OF STEERING DRAUGHT
28. TIP OF STEERING DRAUGHT (RIGHT)
29. STEERING DRAUGHT (RIGHT)
30. WASHER
31. CASING COLLAR
32. CASE CASING
33. THE STEERING DAMPER (ONLY FOR CARS WITH AUTOMATIC TRANSMISSION)
34. LATH
35. CASE CAP (RIGHT)
36. RUBBER ASSEMBLY PLUG
37. CASING PLUG
38. SPRING RING
39. THE DIRECTING PLUG OF THE LATH
40. PLUNZHER
41. SEALING RING
42. SPRING
43. ADJUSTING STOPPER
44. LOCK-NUT

Coupling of a steering shaft

1. COUPLING BOLT
2. COUPLING ASSEMBLED

To remove or disconnect

Fastening of the reechny steering mechanism

45. BOLT
46. COLLAR OF FASTENING OF THE CASE

PERFORMANCE ORDER

1. Negative wire of the storage battery.

2. To lift and properly to fix the car.

3. To turn out two coupling bolts 1 of the coupling 2 and to shift it up on a shaft of a steering column. (Operated wheels should be in the provision of rectilinear movement).

4. Air purifier.

5. To turn out both bolts 25, steering bent for fixing the internal ends to a lath. Before a vyvertyvaniye of bolts to unbend and remove a plate 24 which fixes heads of bolts. The plate 24 will not enclose to a reuse.

6. A steering damper (if it is established on the car).

7. Both collars of fastening of the steering mechanism.

8. A sealing cover 3 from a shaft gear wheel.

9. The steering mechanism assembled through an aperture of a niche of the right wheel.

Prevention

If together with collars of fastening of the steering mechanism bolts were dismantled, it is necessary to screw them on a place and to tighten the moment of 20 Nanometers.

To establish or attach

Fastening of hinges of steering bent for to a lath

23. STEERING DRAUGHT (LEFT)
24. THE FIXING PLATE
25. BOLT
26. BASIC PLATE
29. STEERING DRAUGHT (RIGHT)
32. CASE CASING

Dismantle of steering draft

(ONLY FOR CARS WITH AUTOMATIC TRANSMISSION)

AND. THE PROVISION OF CUTS ON THE FIXING PLATE AT INSTALLATION
CENTURY. WRENCH
PAGE. FOR SIMPLIFICATION OF INSTALLATION TO APPLY A THIN FILM KONSISTENTNA OF GREASING ON THE PLUG

(ONLY FOR CARS WITH THE MANUAL TRANSMISSION)

23. STEERING DRAUGHT (LEFT)
21. THE FIXING PLATE
25. BOLT
26. THE BASIC PLATE (ONLY FOR CARS WITH THE MANUAL TRANSMISSION)
27. PLUG OF THE HINGE OF STEERING DRAUGHT
30. WASHER
32. CASE CASING
33. THE STEERING DAMPER (ONLY FOR CARS WITH AUTOMATIC TRANSMISSION)

PERFORMANCE ORDER

1. The steering mechanism assembled through an aperture of a niche of the right wheel.

2. A sealing cover 3 on a shaft gear wheel.

3. Both collars of fastening of the steering mechanism. (It is necessary to use only new самоконтрящиеся nuts). 3атянуть nuts and bolts of fastening of collars of the steering mechanism moment of 35 Nanometers.

4. A steering damper (if it was established on the car).

5. To establish two washers 30 which should be between a directing level 10 and the internal ends of steering drafts.

6. To attach bolts 25 internal ends of steering drafts 23, 29 to directing level 10. To tighten bolts of fastening of steering bent for to a lath of the steering mechanism the moment of 90 Nanometers.

7. To establish on a basic plate 26 and on heads of bolts 25 fixing plate 24. Cuts on a fixing plate should settle down how is shown on fig. Dismantle of steering draft.

8. To lower and put on the coupling 2 for the end of a shaft gear wheel 5. To tighten bolts of fastening of the coupling of a steering shaft the moment of 25 Nanometers.

9. Air purifier.

10. To lower the car.

11. To attach a negative wire of the storage battery.