Daewoo Nexia

since 1994 of release

Repair and car operation

Deu Neksiya
+ Maintenance instruction
+ Maintenance
+ Engine
+ 3. Engine (two top camshafts)
+ cooling System
+ Toplevnaya and exhaust systems
+ Electric chain
+ 7. Ignition system
+ 8. Electronic control unit and sensors
+ Transmission
+ 10. Five-speed transmission and main RPO MM5 broadcast
+ 11. Automatic Transmission
- Steering
   12.2. General description
   12.3. Reechny steering mechanism assembled
   12.4. Tips of steering drafts
   12.5. Steering drafts
   12.6. Casing of a case of the steering mechanism
   12.7. Coupling of a steering shaft
   12.8. Sealing cover of an opening of a forward board of the Body
   12.9. Plunzher of a lath
   12.10. Shaft gear wheel
   12.11. Lath
   12.12. Needle bearing
   12.13. The directing plug of a lath
   12.14. Verification of the neutral provision of a lath
   12.15. Recommendations about replacement of consolidations in the hydraulic booster
   12.16. Check of level and having added working liquid
   12.17. Air removal from hydrosystem
   12.18. The steering mechanism with the hydraulic booster assembled
   12.19. Hoses and pipelines
   12.20. Tank
   12.21. Tips of steering drafts
   12.22. Steering drafts
   12.23. Plugs of hinges of steering drafts
   12.24. Coupling of a steering shaft
   12.25. Sealing cover
   12.26. Hydrocylinder pipelines
   12.27. Adjustment of a preliminary tightness of a spring of a plunzher
   12.28. Consolidations of a shaft of the hydrodistributor and top bearing
   12.29. Steering mechanism
   12.30. Verification of the neutral provision of a lath
   12.31. Belt of a drive of the pump
   12.32. Pulley of a drive of the pump
   12.33. Pump assembled
   12.34. Control levers on a steering column
   12.35. Steering wheel
   12.36. Ignition lock
   12.37. Steering column
   12.38. Lever switch, steering shaft, steering column (noncontrollable)
   12.39. Lever switch, steering shaft, steering column (adjustable)
+ Running gear
+ 14. Forward suspension bracket
+ 15. Drive of forward wheels
+ 16. Back suspension bracket
+ Brake system
+ Body
+ Heating, ventilation
+ Electric equipment

12.30. Verification of the neutral provision of a lath

GENERAL INFORMATION

Check of installation of operated wheels in situation for rectilinear movement

AND. BRAKE AMPLIFIER
CENTURY. MAIN BRAKE CYLINDER
PAGE. RETURN VACUUM VALVE

20. RUBBER ASSEMBLY PLUG
30. BOLT
44. CASE CASING

After completion of any repair work with the steering mechanism (dismantle and installation, dismantling and assembly) it is necessary to check the neutral provision of a lath corresponding to installation of operated wheels for rectilinear movement of the car.

To adjust

The provision of a lath corresponding to rectilinear movement of the car

AND. AVERAGE PROVISION OF THE LATH

38. BOLT
40. STEERING DRAUGHT (RIGHT)
55. CASE

Verification of the provision of an axis of a coupling bolt of the coupling

AND. THE AXIS OF THE COUPLING BOLT OF THE COUPLING SHOULD SETTLE DOWN HORIZONTALLY

1. COUPLING BOLT
2. COUPLING OF THE STEERING SHAFT
20. RUBBER ASSEMBLY PLUG
35. STEERING DRAUGHT (LEFT)
38. BOLT
40. STEERING DRAUGHT (RIGHT)
44. CASE CASING
55. CASE

Check of correctness of assembly of the steering mechanism

AND. THE WRONG ASSEMBLY OF THE STEERING MECHANISM (THE AXIS OF THE COUPLING BOLT IS NOT HORIZONTAL)

1. COUPLING BOLT
2. COUPLING
20. ASSEMBLY PLUG
35. STEERING DRAUGHT (LEFT)
40. STEERING DRAUGHT (RIGHT)
44. CASE CASING

PERFORMANCE ORDER

1. To establish a level of the control and measuring KM-476 adaptation between heads of steering drafts. Thus the pin of the adaptation should enter into deepening of a seat left (in the direction of the car) the rubber plug.

2. To hold a steering wheel in situation which corresponds to rectilinear movement of the car. At the neutral provision of a lath the size A is equal 325 mm.

3. To check observance of the following conditions:
– a coupling bolt klemmovy connect a niya of the coupling should settle down from above a steering shaft, and its axis should be horizontal;
– cпицы of a steering wheel should be symmetrized concerning a vertical and to be directed down.
If the axis of a coupling bolt is located obliquely, assembly of the steering mechanism is made incorrectly (with shift on one or several teeths of a lath). In this case it is necessary to dismantle a shaft gear wheel and anew to assemble the mechanism.
If the coupling bolt of the coupling is located horizontally, and spokes of a steering wheel are asymmetrical concerning a vertical (reject scientific research institute makes more than 5 degrees), it is necessary to remove a steering wheel from a steering shaft, to center and establish it anew.