Daewoo Nexia

since 1994 of release

Repair and car operation

Deu Neksiya
+ Maintenance instruction
+ Maintenance
+ Engine
+ 3. Engine (two top camshafts)
+ cooling System
+ Toplevnaya and exhaust systems
+ Electric chain
+ 7. Ignition system
+ 8. Electronic control unit and sensors
+ Transmission
+ 10. Five-speed transmission and main RPO MM5 broadcast
+ 11. Automatic Transmission
- Steering
   12.2. General description
   12.3. Reechny steering mechanism assembled
   12.4. Tips of steering drafts
   12.5. Steering drafts
   12.6. Casing of a case of the steering mechanism
   12.7. Coupling of a steering shaft
   12.8. Sealing cover of an opening of a forward board of the Body
   12.9. Plunzher of a lath
   12.10. Shaft gear wheel
   12.11. Lath
   12.12. Needle bearing
   12.13. The directing plug of a lath
   12.14. Verification of the neutral provision of a lath
   12.15. Recommendations about replacement of consolidations in the hydraulic booster
   12.16. Check of level and having added working liquid
   12.17. Air removal from hydrosystem
   12.18. The steering mechanism with the hydraulic booster assembled
   12.19. Hoses and pipelines
   12.20. Tank
   12.21. Tips of steering drafts
   12.22. Steering drafts
   12.23. Plugs of hinges of steering drafts
   12.24. Coupling of a steering shaft
   12.25. Sealing cover
   12.26. Hydrocylinder pipelines
   12.27. Adjustment of a preliminary tightness of a spring of a plunzher
   12.28. Consolidations of a shaft of the hydrodistributor and top bearing
   12.29. Steering mechanism
   12.30. Verification of the neutral provision of a lath
   12.31. Belt of a drive of the pump
   12.32. Pulley of a drive of the pump
   12.33. Pump assembled
   12.34. Control levers on a steering column
   12.35. Steering wheel
   12.36. Ignition lock
   12.37. Steering column
   12.38. Lever switch, steering shaft, steering column (noncontrollable)
   12.39. Lever switch, steering shaft, steering column (adjustable)
+ Running gear
+ 14. Forward suspension bracket
+ 15. Drive of forward wheels
+ 16. Back suspension bracket
+ Brake system
+ Body
+ Heating, ventilation
+ Electric equipment

12.6. Casing of a case of the steering mechanism

To remove or disconnect

Dismantle of a casing and directing level

AND. THE FLUTE ON THE CASE FOR PLUG INSTALLATION
CENTURY. A FLUTE ON THE CASE FOR PLUG INSTALLATION (FROM THE STEERING MECHANISM)

8. CASE CAP (LEFT)
10. THE DIRECTING LEVEL OF THE LATH
16. CASING PLUG
17. CASING COLLAR
30. WASHER
31. CASING COLLAR
32. CASE CASING
33. THE STEERING DAMPER (ONLY FOR CARS WITH AUTOMATIC TRANSMISSION)
35. REZINOV AI ASSEMBLY PLUG
37. CASING PLUG

PERFORMANCE ORDER

1. To disconnect and remove the right rubber plug 36. The left plug 9 should not be dismantled, if it does not need replacement.

2. To cut off and throw out collars 17 and 31.

3. To pull together a casing 32 over the plug 37 from a case of the 7th helmsman of the mechanism.

4. The plug 37 should not be dismantled, if it is not damaged.

5. The cap 8 should be dismantled from a case, only if it has defects.

To establish or attach

PERFORMANCE ORDER

1. To take out the plug 16 of a casing.

2. To put on a casing a new collar 17. To establish in a casing the plug 16.

3. The new plug 37 on a case if the old plug was dismantled.

4. Directing level 10 on a lath.

5. For simplification of assembly to grease внутрен a ny edge of the plug 37 with a thin layer of konsistentny greasing.

6. A casing 32 on a case 7.

7. For simplification of assembly partially to screw bolts 25 in a lath, previously having put on them washers. It is necessary for fixing of the correct provision of a lath 34, a level 10 and a casing 32.

8. To shift a casing 32 along a case up to the end so that the plug 16 sat down in the assembly flute executed on a case. To tighten a new collar 17 by means of the KM-J-26610 adaptation.

9. To put on other end of a casing the plug 37 established on a train. To put on and tighten by means of the KM-2b610 adaptation a new collar.