Daewoo Nexia

since 1994 of release

Repair and car operation

Deu Neksiya
+ Maintenance instruction
+ Maintenance
+ Engine
+ 3. Engine (two top camshafts)
+ cooling System
+ Toplevnaya and exhaust systems
+ Electric chain
+ 7. Ignition system
+ 8. Electronic control unit and sensors
+ Transmission
+ 10. Five-speed transmission and main RPO MM5 broadcast
+ 11. Automatic Transmission
- Steering
   12.2. General description
   12.3. Reechny steering mechanism assembled
   12.4. Tips of steering drafts
   12.5. Steering drafts
   12.6. Casing of a case of the steering mechanism
   12.7. Coupling of a steering shaft
   12.8. Sealing cover of an opening of a forward board of the Body
   12.9. Plunzher of a lath
   12.10. Shaft gear wheel
   12.11. Lath
   12.12. Needle bearing
   12.13. The directing plug of a lath
   12.14. Verification of the neutral provision of a lath
   12.15. Recommendations about replacement of consolidations in the hydraulic booster
   12.16. Check of level and having added working liquid
   12.17. Air removal from hydrosystem
   12.18. The steering mechanism with the hydraulic booster assembled
   12.19. Hoses and pipelines
   12.20. Tank
   12.21. Tips of steering drafts
   12.22. Steering drafts
   12.23. Plugs of hinges of steering drafts
   12.24. Coupling of a steering shaft
   12.25. Sealing cover
   12.26. Hydrocylinder pipelines
   12.27. Adjustment of a preliminary tightness of a spring of a plunzher
   12.28. Consolidations of a shaft of the hydrodistributor and top bearing
   12.29. Steering mechanism
   12.30. Verification of the neutral provision of a lath
   12.31. Belt of a drive of the pump
   12.32. Pulley of a drive of the pump
   12.33. Pump assembled
   12.34. Control levers on a steering column
   12.35. Steering wheel
   12.36. Ignition lock
   12.37. Steering column
   12.38. Lever switch, steering shaft, steering column (noncontrollable)
   12.39. Lever switch, steering shaft, steering column (adjustable)
+ Running gear
+ 14. Forward suspension bracket
+ 15. Drive of forward wheels
+ 16. Back suspension bracket
+ Brake system
+ Body
+ Heating, ventilation
+ Electric equipment

12.28. Consolidations of a shaft of the hydrodistributor and top bearing

GENERAL INFORMATION

Consolidations of a shaft of the hydrodistributor and top bearing

AND. THE BEARING IS PRESSED IN THE PLUG. DISMANTLING OF CONNECTION IS MADE ONLY IN NEED OF BEARING REPLACEMENT

4. SPRING RING
5. CONSOLIDATION (BOOT) VALA-SHESTERNI
6. INTERNAL CONSOLIDATION VALA-SHESTERNI
7. THE BEARING IN THE PLUG
21. NUT
24. CAP

To remove or disconnect

PERFORMANCE ORDER

1. Steering mechanism assembled. See fig. of Reechny the steering mechanism with the hydraulic amplifier.

2. A lock-nut 16 from a stopper 17.

3. A stopper 17 from a case 55.

4. A spring 18, a plunzher 14 with a sealing ring 15 from a case.

5. A spring ring 4 from a flute of a case 55.

6. A cap 24 from a case 55.

7. Holding a shaft in motionless situation, to unscrew a nut 21 from a shaft gear wheel.

Prevention

Otvorachivaniye 21 without fixing of a shaft gear wheel can lead nuts to breakage of teeths of a gear wheel of the helmsman механиз ма. By means of a press to press a carving shaft of a shaft gear wheel and выпрессовать from the bearing 22 a shaft neck.

Carrying out complete dismantle of a shaft gear wheel assembled with the distributor is not required.

8. A boot 5, internal consolidation 6 and the bearing 7 from a case 55.

To establish or attach

PERFORMANCE ORDER

1. The distributor assembled 10 in a case 55.

2. Holding a distributor shaft, to screw a nut 21 on a shaft gear wheel.

Prevention

Holding a distributor shaft in motionless situation, to tighten a nut 21 moment of 30 Nanometers. The inhaling of a nut 21 without fixing of a shaft gear wheel can lead to breakage of teeths of a gear wheel of the steering mechanism.

3. A cap 24 in a case 55.

4. The top bearing 7 on a shaft of the distributor and in a nest of a case 55.

5. Protective cap J-34614 on a distributor shaft.

6. Consolidation 6 and a boot 5 on a protective cap in a case 55.

7. A spring ring 4 in a flute of a case 55.

8. To grease with lithium konsistentny greasing a plunzher 14, a sealing ring 15, a spring 18 and an adjusting stopper 17.

9. Plunzher 14 with a sealing ring 15, a spring 18 and an adjusting stopper 17 in a case 55.

10. Having established a lath in average situation, to wrap clockwise an adjusting stopper 17 against the stop in a case. Then to unscrew a stopper on 30–40 degrees. Проворить size of the moment of a friction on a shaft of the steering mechanism. The maximum size of the moment of a friction from a preliminary tightness of a spring of a plunzher should not exceed 1,8 Nanometers.

11. To screw a lock-nut 16 on a stopper 17. Holding a stopper, to tighten a lock-nut the moment of 70 Nanometers.

12. The steering mechanism assembled on the car.