| 1. To clear of dirt an external surface of a tank of the main brake cylinder and the next details. |
| 2. To uncover a tank. |
| 3. To check level of brake liquid. If necessary to add in a tank brake liquid, interchangeable with DOT 3 brand liquid, and to finish level to norm. |
| 4. To establish into place a tank cover. |
| 5. To remove air from the block of hydraulic modulators (see fig. Air removal from the block of modulators). |
| 5а. To put on the union of the back valve for production of air pure plasticity a vy hose. Other end of a hose to lower in pure capacity, partially |
| 5б. Slowly to unscrew the valve of production of air on 1/2–3/4 turns. |
| 5в. To press by means of the assistant a brake pedal and to hold her in the pressed situation until brake liquid will start to leave. |
| 5г. To wrap the valve of production of air and to release a brake pedal. To repeat operations B and Several times, brake liquid without air vials yet will not start to leave. To tighten the valve of production of air the moment of 9 Nanometers. |
5д. To repeat the described operations for the forward valve of production of air.
Prevention
Exit of brake liquid from both valves of production of air the witness ствует that cavities of modulators are filled with liquid. But it yet does not guarantee total absence of air in the block of modulators. After carrying out the described operations it is necessary to pass to air removal from wheel brake cylinders which are located below the block of modulators. Having pumped over wheel cylinders, it is necessary to let out finally the remained air from cavities of modulators.
|
| 6. To uncover a tank with brake liquid. |
| 7. To check level of brake liquid. If necessary to add in a tank brake liquid, interchangeable with DOT 3 brand liquid, and to finish level to norm. |
| 8. To establish into place a tank cover. |
9. To lift and fix properly the car.
Prevention
Air removal from wheel brake cylinders is necessary for carrying out in the following sequence:
– cylinder of the right back wheel;
– cylinder of the left back wheel;
– cylinder of the right forward wheel;
– cylinder of the left forward wheel.
|
| 10. To remove air from wheel cylinders of drum-type and disk brakes, fig. Air removal from the working cylinder of a back wheel and fig. Air removal from the working cylinder of a forward wheel. |
| 10а. To put on the union of the valve of production of air a pure plastic hose. Other end of a hose to lower in the pure capacity which has been partially filled with brake liquid. |
| 10б. To open the valve of production of air. |
| 10в. Slowly to press by means of the assistant a brake pedal. |
| 10г. To wrap the valve of production of air and to release a brake pedal. |
| 10д. After a 5-second pause to repeat operations B, B and G, including выдержива pause scientific research institute, several times, while the brake pedal does not become "rigid" and the hose will cease to leave together with brake liquid air vials. To tighten the valve of production of air the moment of 9 Nanometers. |
| 10е. To repeat operations A – Д for other wheel cylinders (the left back wheel and both forward wheels). |
| 11. To lower the car. |
| 12. To uncover a tank with brake liquid. |
| 13. To check level of brake liquid. If necessary to add in a tank brake liquid, interchangeable with DOT 3 brand liquid, and to finish level to norm. |
| 14. To establish into place a tank cover. |
| 15. To remove air from the block of hydraulic modulators (see fig. Air removal from the block of modulators). |
| 15а. To put on the union of the back valve for production of air pure plasticity a vy hose. Other end of a hose to lower in the pure capacity which has been partially filled with brake liquid. |
| 15б. Slowly to unscrew the valve of production of air on 1/2-3/4 turns. |
| 15в. To press by means of the assistant a brake pedal and to hold her in the pressed situation until brake liquid will start to leave. |
| 15г. To wrap the valve of production of air and to release a brake pedal. To repeat operations B and Several times, brake liquid without air vials yet will not start to leave. To tighten the valve of production of air the moment of 9 Nanometers. |
| 15д. To repeat the described operations for the forward valve of production of air. |
| 16. To uncover a tank with brake liquid. |
| 17. To check level of brake liquid. If necessary to add in a tank brake liquid, interchangeable with DOT 3 brand liquid, and to finish level to norm. |
| 18. To establish into place a tank cover. |
| 19. To include ignition, to press a brake pedal with average effort and to hold her in the pressed situation. To pay attention to a course and resistance of a pedal. If a pedal "rigid" and a course its small to start the Engine. At the working engine once again to check a pedal course. If a pedal still "rigid" and a course its small to pass to operation 20. If a brake pedal "soft" or its its course is unduly great at the unemployed or the working engine, it is necessary to give by means of the SCANNER-11 device command for a rastormazhivaniye, then for a zatormazhivaniye of wheels three times in a row. After that 10 times to switch on and off EMK. To bring pistons of modulators into extreme top situation and to repeat operations on air removal from a brake hydraulic actuator. |
| 20. To test the car run. To execute some office braking (without ABS inclusion) since moderate initial speed for check of normal functioning of brake system. |
