Daewoo Nexia

since 1994 of release

Repair and car operation


Deu Neksiya
+ Maintenance instruction
+ Maintenance
+ Engine
+ 3. Engine (two top camshafts)
+ cooling System
+ Toplevnaya and exhaust systems
+ Electric chain
+ 7. Ignition system
+ 8. Electronic control unit and sensors
+ Transmission
+ 10. Five-speed transmission and main RPO MM5 broadcast
+ 11. Automatic Transmission
+ Steering
+ Running gear
+ 14. Forward suspension bracket
+ 15. Drive of forward wheels
+ 16. Back suspension bracket
+ Brake system
- Body
   18.2. Identification and use of keys
   18.3. Pasted lateral moldings
   18.4. Diagnostics and repair of a leakage of the Body
   18.5. Anticorrosive processing
   + 18.6. Dismantle of consolidations of wind and back glasses
   + 18.7. Windscreen
   + 18.8. Back glass (Body sedan)
   18.9. Glass of a back door (Body hatch-back)
   18.10. Triangular lateral glass
   + 18.11. Elimination of a leakage of consolidations
   + 18.12. Rear-view mirror
   - 18.13. Electroheater of back glass
      18.13.1. Check of serviceability of electrocarrying-out strips of a heater
      18.13.2. Repair of electrocarrying-out strips of a heater
      18.13.3. Repair of a feeding wire
   + 18.14. Bumpers
   18.15. External ventilating lattice
   18.16. Switch of a forward door
   18.17. Cowl
   18.18. Cowl loops
   18.19. Cowl emphasis
   18.20. Locking device of a cowl
   18.21. Safety latch of a cowl
   18.22. Cable of a latch of a cowl
   18.23. Front grille
   18.24. Forward wing
   + 18.25. Panels of an upholstery of doors
   + 18.26. Equipment of doors (lobbies and back doors)
   + 18.27. Door locks
   + 18.28. Glasses of doors
   18.29. External rear-view mirrors
   18.30. Dismantle and installation of lobbies and back doors
   + 18.31. Back panels of an upholstery (Body hatch-back)
   + 18.32. Upholstery panels (Body sedan)
   18.33. External panel
   18.34. Ventilating valve (Body hatch-back)
   18.35. Hatch of a mouth of a fuel tank
   + 18.36. Opening window leaves (A body a hatch-back)
   + 18.37. Back shelf (Body sedan)
   18.38. Cover of a luggage compartment (Body hatch-back)
   18.39. Overlay of a back wall of a luggage carrier (Body sedan)
   + 18.40. Trunk lid (Body sedan)
   18.41. The back combined lamp
   + 18.42. Back door (Body hatch-back)
   18.43. Roof
   18.44. Ceiling panel
   18.45. Antisolar peaks
   18.46. Plafond of internal lighting
   + 18.47. Panels and salon equipment
   18.48. External longitudinal overlays of a roof
   + 18.49. Ventilating hatch
   + 18.50. Forward seats
   + 18.51. Back seat
+ Heating, ventilation
+ Electric equipment


8128da4b



18.13.3. Repair of a feeding wire
GENERAL INFORMATION

The feeding wire of an electroheater of back glass can be again attached to the tire by means of the soldering. For the soldering it is necessary to use the solder containing 3 % of silver, and kanifolny paste as gumboil.

PERFORMANCE ORDER
1. Before the soldering of a wire it is necessary to clear the repaired place of a strip.
2. With a brush to put on connected places of a wire and the tire a small amount of kanifolny paste.
3. To put for the wire end solder. Thus it is not necessary to overheat a wire and to bring excessive amount of solder.
4. To solder a wire to the tire, avoiding an overheat of connected details.