Daewoo Nexia

since 1994 of release

Repair and car operation



Deu Neksiya
+ Maintenance instruction
+ Maintenance
+ Engine
+ 3. Engine (two top camshafts)
+ cooling System
+ Toplevnaya and exhaust systems
+ Electric chain
+ 7. Ignition system
+ 8. Electronic control unit and sensors
+ Transmission
+ 10. Five-speed transmission and main RPO MM5 broadcast
+ 11. Automatic Transmission
+ Steering
+ Running gear
+ 14. Forward suspension bracket
+ 15. Drive of forward wheels
+ 16. Back suspension bracket
+ Brake system
- Body
   18.2. Identification and use of keys
   18.3. Pasted lateral moldings
   18.4. Diagnostics and repair of a leakage of the Body
   18.5. Anticorrosive processing
   + 18.6. Dismantle of consolidations of wind and back glasses
   + 18.7. Windscreen
   + 18.8. Back glass (Body sedan)
   18.9. Glass of a back door (Body hatch-back)
   18.10. Triangular lateral glass
   + 18.11. Elimination of a leakage of consolidations
   + 18.12. Rear-view mirror
   - 18.13. Electroheater of back glass
      18.13.1. Check of serviceability of electrocarrying-out strips of a heater
      18.13.2. Repair of electrocarrying-out strips of a heater
      18.13.3. Repair of a feeding wire
   + 18.14. Bumpers
   18.15. External ventilating lattice
   18.16. Switch of a forward door
   18.17. Cowl
   18.18. Cowl loops
   18.19. Cowl emphasis
   18.20. Locking device of a cowl
   18.21. Safety latch of a cowl
   18.22. Cable of a latch of a cowl
   18.23. Front grille
   18.24. Forward wing
   + 18.25. Panels of an upholstery of doors
   + 18.26. Equipment of doors (lobbies and back doors)
   + 18.27. Door locks
   + 18.28. Glasses of doors
   18.29. External rear-view mirrors
   18.30. Dismantle and installation of lobbies and back doors
   + 18.31. Back panels of an upholstery (Body hatch-back)
   + 18.32. Upholstery panels (Body sedan)
   18.33. External panel
   18.34. Ventilating valve (Body hatch-back)
   18.35. Hatch of a mouth of a fuel tank
   + 18.36. Opening window leaves (A body a hatch-back)
   + 18.37. Back shelf (Body sedan)
   18.38. Cover of a luggage compartment (Body hatch-back)
   18.39. Overlay of a back wall of a luggage carrier (Body sedan)
   + 18.40. Trunk lid (Body sedan)
   18.41. The back combined lamp
   + 18.42. Back door (Body hatch-back)
   18.43. Roof
   18.44. Ceiling panel
   18.45. Antisolar peaks
   18.46. Plafond of internal lighting
   + 18.47. Panels and salon equipment
   18.48. External longitudinal overlays of a roof
   + 18.49. Ventilating hatch
   + 18.50. Forward seats
   + 18.51. Back seat
+ Heating, ventilation
+ Electric equipment


8128da4b



18.13.2. Repair of electrocarrying-out strips of a heater

GENERAL INFORMATION

Repair of electrocarrying-out strips of a heater

1. STICKY TAPE
2. THE DAMAGED STRIP
3. WOODEN SHOVEL
4. REPAIR INSERT

PERFORMANCE ORDER
1. To disconnect a food wire from an electroheater of back glass.
2. To check serviceability of electrocarrying-out strips of a heater.
3. To note places of damages of strips by means of a pencil-steklografa or a piece of chalk (on the outer side of back glass).
Prevention

To remove the damaged site of a strip at length about 6 mm from each party from a gap. To wipe the damaged place the pure fabric moistened with alcohol.


4. To paste on the damaged place a repair sticky tape or two pieces of a usual sticky tape from above and from below from a repaired strip. The sticky tape is necessary for restriction of width of a repair zone.
When using a special repair tape it is necessary to be convinced that the width of a cut in it corresponds to width of a repaired electrocarrying-out strip. To uncover boxes in which materials for repair of electrocarrying-out strips are stored.
5. Carefully to mix a hardener with the main structure of silvery color. In case of crystallization of a hardener it is necessary to ship packing with it in hot water and to wait, while the hardener again becomes liquid.
6. At room temperature to put on the damaged place repair composition by means of a small wooden stick or a shovel.
7. Carefully to remove protective sticky tapes.
Prevention

Polymerization of repair composition should occur in heat. In order to avoid damage of an upholstery of salon from a source of heat it is necessary to establish filters. To heat up the damaged place within 1–2 minutes. A heating element it is necessary to have at distance of 25 mm from the damaged place. Minimum necessary temperature of heating makes 149 ° Page.


8. To check the repaired place of an electrocarrying-out strip. If the strip became colourless, it is necessary to put нa it by means of a brush tinting structure. After a podsykhaniye during 30 with to wipe a pure not fleecy fabric surpluses of tinting structure. To include and check work of an electroheater of back glass.
Prevention

Full of polymerization of repair composition not less than 24 hours proceed. During this time it is necessary to exclude mechanical impact on the repaired place of a strip.