Daewoo Nexia

since 1994 of release

Repair and car operation



Deu Neksiya
+ Maintenance instruction
+ Maintenance
+ Engine
+ 3. Engine (two top camshafts)
+ cooling System
+ Toplevnaya and exhaust systems
+ Electric chain
+ 7. Ignition system
+ 8. Electronic control unit and sensors
+ Transmission
+ 10. Five-speed transmission and main RPO MM5 broadcast
+ 11. Automatic Transmission
+ Steering
+ Running gear
+ 14. Forward suspension bracket
+ 15. Drive of forward wheels
+ 16. Back suspension bracket
+ Brake system
- Body
   18.2. Identification and use of keys
   18.3. Pasted lateral moldings
   18.4. Diagnostics and repair of a leakage of the Body
   18.5. Anticorrosive processing
   + 18.6. Dismantle of consolidations of wind and back glasses
   + 18.7. Windscreen
   + 18.8. Back glass (Body sedan)
   18.9. Glass of a back door (Body hatch-back)
   18.10. Triangular lateral glass
   - 18.11. Elimination of a leakage of consolidations
      18.11.2. Cleaning
      18.11.3. Installation or accession
      18.11.4. Check
   + 18.12. Rear-view mirror
   + 18.13. Electroheater of back glass
   + 18.14. Bumpers
   18.15. External ventilating lattice
   18.16. Switch of a forward door
   18.17. Cowl
   18.18. Cowl loops
   18.19. Cowl emphasis
   18.20. Locking device of a cowl
   18.21. Safety latch of a cowl
   18.22. Cable of a latch of a cowl
   18.23. Front grille
   18.24. Forward wing
   + 18.25. Panels of an upholstery of doors
   + 18.26. Equipment of doors (lobbies and back doors)
   + 18.27. Door locks
   + 18.28. Glasses of doors
   18.29. External rear-view mirrors
   18.30. Dismantle and installation of lobbies and back doors
   + 18.31. Back panels of an upholstery (Body hatch-back)
   + 18.32. Upholstery panels (Body sedan)
   18.33. External panel
   18.34. Ventilating valve (Body hatch-back)
   18.35. Hatch of a mouth of a fuel tank
   + 18.36. Opening window leaves (A body a hatch-back)
   + 18.37. Back shelf (Body sedan)
   18.38. Cover of a luggage compartment (Body hatch-back)
   18.39. Overlay of a back wall of a luggage carrier (Body sedan)
   + 18.40. Trunk lid (Body sedan)
   18.41. The back combined lamp
   + 18.42. Back door (Body hatch-back)
   18.43. Roof
   18.44. Ceiling panel
   18.45. Antisolar peaks
   18.46. Plafond of internal lighting
   + 18.47. Panels and salon equipment
   18.48. External longitudinal overlays of a roof
   + 18.49. Ventilating hatch
   + 18.50. Forward seats
   + 18.51. Back seat
+ Heating, ventilation
+ Electric equipment


8128da4b



18.11. Elimination of a leakage of consolidations

GENERAL INFORMATION

Repair of not tight consolidation

AND. THE EXISTING LAYER OF PRESSURIZING STRUCTURE
CENTURY. REMOVAL OF THE EXTERNAL LAYER OF PRESSURIZING STRUCTURE
PAGE. DRAWING OF THE PRIMING COAT
D. DRAWING OF THE REPAIR LAYER OF PRESSURIZING STRUCTURE
Е. FLAT SHOVEL
F. TO DISTRIBUTE AND PRESS PRESSURIZING STRUCTURE INTO CRACKS

In certain cases the leakage of consolidations can be eliminated without dismantle and the subsequent installation of glasses. This way of repair is applicable only to the glasses established on uretanovy pressurizing structure, and demands application of materials from a repair glutinous set.

PERFORMANCE ORDER
1. To remove a molding closing a place of a leak. In certain cases dismantle of additional details can be demanded to localize a leak place.
2. To note not tight place. Carefully to press from within glass, to specify extent of defect of consolidation. At this time glass should pour down outside water. To note extent of the damaged place.
3. To wash out water a zone adjacent to not tight place, from dirt and extraneous substances. Then to dry a current of air.
4. By means of a sharp knife to remove from a defective place pressurizing structure on length of 75-100 mm (from both parties).
5. To put on the damaged place a priming coat, using materials from a repair set. Before use it is necessary to mix packing contents. To dry within 5 minutes.
6. To put from two parties pressurizing structure on the damaged place (on length of 75-100 mm).
7. At once after drawing to distribute and press pressurizing structure into cracks between glass and a frame of a window aperture for ensuring tightness of connection. To use for this purpose a flat shovel or other suitable tool.
8. By means of a stream of warm or hot water to check tightness of consolidation. It is not necessary to direct a strong stream of water on svezhenanesenny pressurizing structure.
9. To establish into place everything previously the dismantled details.