|
|
Daewoo Nexiasince 1994 of releaseRepair and car operation |
|
|
Deu Neksiya + Maintenance instruction + Maintenance + Engine + 3. Engine (two top camshafts) + cooling System + Toplevnaya and exhaust systems + Electric chain + 7. Ignition system + 8. Electronic control unit and sensors + Transmission + 10. Five-speed transmission and main RPO MM5 broadcast + 11. Automatic Transmission + Steering + Running gear + 14. Forward suspension bracket + 15. Drive of forward wheels + 16. Back suspension bracket + Brake system - Body 18.2. Identification and use of keys 18.3. Pasted lateral moldings 18.4. Diagnostics and repair of a leakage of the Body 18.5. Anticorrosive processing + 18.6. Dismantle of consolidations of wind and back glasses + 18.7. Windscreen + 18.8. Back glass (Body sedan) 18.9. Glass of a back door (Body hatch-back) 18.10. Triangular lateral glass + 18.11. Elimination of a leakage of consolidations + 18.12. Rear-view mirror + 18.13. Electroheater of back glass + 18.14. Bumpers 18.15. External ventilating lattice 18.16. Switch of a forward door 18.17. Cowl 18.18. Cowl loops 18.19. Cowl emphasis 18.20. Locking device of a cowl 18.21. Safety latch of a cowl 18.22. Cable of a latch of a cowl 18.23. Front grille 18.24. Forward wing + 18.25. Panels of an upholstery of doors + 18.26. Equipment of doors (lobbies and back doors) - 18.27. Door locks 18.27.2. Door locks of lobbies and back doors 18.27.3. The internal handle of the lock - lobbies and back doors 18.27.4. Draft of blocking of the lock – lobbies and back doors 18.27.5. The external handle of the door lock – lobbies and back doors + 18.27.6. The lock cylinder – lobbies and back doors 18.27.7. Assembly of the door lock + 18.28. Glasses of doors 18.29. External rear-view mirrors 18.30. Dismantle and installation of lobbies and back doors + 18.31. Back panels of an upholstery (Body hatch-back) + 18.32. Upholstery panels (Body sedan) 18.33. External panel 18.34. Ventilating valve (Body hatch-back) 18.35. Hatch of a mouth of a fuel tank + 18.36. Opening window leaves (A body a hatch-back) + 18.37. Back shelf (Body sedan) 18.38. Cover of a luggage compartment (Body hatch-back) 18.39. Overlay of a back wall of a luggage carrier (Body sedan) + 18.40. Trunk lid (Body sedan) 18.41. The back combined lamp + 18.42. Back door (Body hatch-back) 18.43. Roof 18.44. Ceiling panel 18.45. Antisolar peaks 18.46. Plafond of internal lighting + 18.47. Panels and salon equipment 18.48. External longitudinal overlays of a roof + 18.49. Ventilating hatch + 18.50. Forward seats + 18.51. Back seat + Heating, ventilation + Electric equipment 
|
18.27. Door locks18.27.1. Locking bolt
Locking bolt of the door lock
The locking bolt with washers is screwed in the floating plate established on a back rack of a doorway. The floating plate provides adjustment of provision of a locking bolt both in vertical, and in the cross-section direction. Door locking in a closed position occurs, when the lock fork is hooked by the cut with a head of a locking bolt.
Vertical and cross-section adjustment of a locking bolt Increase in diameter of an opening for a locking bolt
Need for vertical or cross-section adjustment of a locking bolt can arise for several reasons: Body deformation as a result of failure, replacement of a sealant of a door which can affect operation of the lock, complaints to the increased aerodynamic noise or difficulties when opening and closing door etc. For vertical and cross-section adjustment of a locking bolt it is necessary to execute the following.
|
|