Daewoo Nexia

since 1994 of release

Repair and car operation



Deu Neksiya
+ Maintenance instruction
+ Maintenance
+ Engine
+ 3. Engine (two top camshafts)
+ cooling System
+ Toplevnaya and exhaust systems
+ Electric chain
+ 7. Ignition system
+ 8. Electronic control unit and sensors
+ Transmission
+ 10. Five-speed transmission and main RPO MM5 broadcast
+ 11. Automatic Transmission
+ Steering
+ Running gear
+ 14. Forward suspension bracket
+ 15. Drive of forward wheels
+ 16. Back suspension bracket
+ Brake system
- Body
   18.2. Identification and use of keys
   18.3. Pasted lateral moldings
   18.4. Diagnostics and repair of a leakage of the Body
   18.5. Anticorrosive processing
   + 18.6. Dismantle of consolidations of wind and back glasses
   + 18.7. Windscreen
   + 18.8. Back glass (Body sedan)
   18.9. Glass of a back door (Body hatch-back)
   18.10. Triangular lateral glass
   + 18.11. Elimination of a leakage of consolidations
   + 18.12. Rear-view mirror
   + 18.13. Electroheater of back glass
   + 18.14. Bumpers
   18.15. External ventilating lattice
   18.16. Switch of a forward door
   18.17. Cowl
   18.18. Cowl loops
   18.19. Cowl emphasis
   18.20. Locking device of a cowl
   18.21. Safety latch of a cowl
   18.22. Cable of a latch of a cowl
   18.23. Front grille
   18.24. Forward wing
   + 18.25. Panels of an upholstery of doors
   + 18.26. Equipment of doors (lobbies and back doors)
   - 18.27. Door locks
      18.27.2. Door locks of lobbies and back doors
      18.27.3. The internal handle of the lock - lobbies and back doors
      18.27.4. Draft of blocking of the lock – lobbies and back doors
      18.27.5. The external handle of the door lock – lobbies and back doors
      + 18.27.6. The lock cylinder – lobbies and back doors
      18.27.7. Assembly of the door lock
   + 18.28. Glasses of doors
   18.29. External rear-view mirrors
   18.30. Dismantle and installation of lobbies and back doors
   + 18.31. Back panels of an upholstery (Body hatch-back)
   + 18.32. Upholstery panels (Body sedan)
   18.33. External panel
   18.34. Ventilating valve (Body hatch-back)
   18.35. Hatch of a mouth of a fuel tank
   + 18.36. Opening window leaves (A body a hatch-back)
   + 18.37. Back shelf (Body sedan)
   18.38. Cover of a luggage compartment (Body hatch-back)
   18.39. Overlay of a back wall of a luggage carrier (Body sedan)
   + 18.40. Trunk lid (Body sedan)
   18.41. The back combined lamp
   + 18.42. Back door (Body hatch-back)
   18.43. Roof
   18.44. Ceiling panel
   18.45. Antisolar peaks
   18.46. Plafond of internal lighting
   + 18.47. Panels and salon equipment
   18.48. External longitudinal overlays of a roof
   + 18.49. Ventilating hatch
   + 18.50. Forward seats
   + 18.51. Back seat
+ Heating, ventilation
+ Electric equipment


8128da4b чит на кс го купить, go.
It рекрутеры еще здесь.



18.27.7. Assembly of the door lock

PERFORMANCE ORDER
1. To grease with konsistentny greasing an internal surface of an opening of the case of the lock and to insert into it the cylinder with a key.
Prevention

At cylinder assembly with the case of the lock to check correctness of a relative arrangement of openings for moisture removal, fig. Arrangement of a returnable spring and fig. Cylinder of the door lock.


2. To establish a returnable spring on the top part of the case of the lock. On the locks intended for the left doors, pads of a spring should be visible to the left of openings for moisture removal (if to look from above). On the locks intended for the right doors, pads of a spring should be located to the right of openings for moisture removal, fig. Arrangement of a returnable spring.
3. To establish on the lock cylinder an arm so that its lever was turned to the left on locks for the left doors and – to the right on the locks intended for the right doors.
Prevention

Arms can differ color: white for locks of the left doors and black for locks of the right doors.