Daewoo Nexia

since 1994 of release

Repair and car operation

Deu Neksiya
+ Maintenance instruction
+ Maintenance
+ Engine
+ 3. Engine (two top camshafts)
+ cooling System
+ Toplevnaya and exhaust systems
+ Electric chain
+ 7. Ignition system
+ 8. Electronic control unit and sensors
+ Transmission
+ 10. Five-speed transmission and main RPO MM5 broadcast
+ 11. Automatic Transmission
+ Steering
+ Running gear
+ 14. Forward suspension bracket
+ 15. Drive of forward wheels
+ 16. Back suspension bracket
+ Brake system
- Body
   18.2. Identification and use of keys
   18.3. Pasted lateral moldings
   18.4. Diagnostics and repair of a leakage of the Body
   18.5. Anticorrosive processing
   + 18.6. Dismantle of consolidations of wind and back glasses
   + 18.7. Windscreen
   - 18.8. Back glass (Body sedan)
      18.8.1. Windscreen consolidation
   18.9. Glass of a back door (Body hatch-back)
   18.10. Triangular lateral glass
   + 18.11. Elimination of a leakage of consolidations
   + 18.12. Rear-view mirror
   + 18.13. Electroheater of back glass
   + 18.14. Bumpers
   18.15. External ventilating lattice
   18.16. Switch of a forward door
   18.17. Cowl
   18.18. Cowl loops
   18.19. Cowl emphasis
   18.20. Locking device of a cowl
   18.21. Safety latch of a cowl
   18.22. Cable of a latch of a cowl
   18.23. Front grille
   18.24. Forward wing
   + 18.25. Panels of an upholstery of doors
   + 18.26. Equipment of doors (lobbies and back doors)
   + 18.27. Door locks
   + 18.28. Glasses of doors
   18.29. External rear-view mirrors
   18.30. Dismantle and installation of lobbies and back doors
   + 18.31. Back panels of an upholstery (Body hatch-back)
   + 18.32. Upholstery panels (Body sedan)
   18.33. External panel
   18.34. Ventilating valve (Body hatch-back)
   18.35. Hatch of a mouth of a fuel tank
   + 18.36. Opening window leaves (A body a hatch-back)
   + 18.37. Back shelf (Body sedan)
   18.38. Cover of a luggage compartment (Body hatch-back)
   18.39. Overlay of a back wall of a luggage carrier (Body sedan)
   + 18.40. Trunk lid (Body sedan)
   18.41. The back combined lamp
   + 18.42. Back door (Body hatch-back)
   18.43. Roof
   18.44. Ceiling panel
   18.45. Antisolar peaks
   18.46. Plafond of internal lighting
   + 18.47. Panels and salon equipment
   18.48. External longitudinal overlays of a roof
   + 18.49. Ventilating hatch
   + 18.50. Forward seats
   + 18.51. Back seat
+ Heating, ventilation
+ Electric equipment

18.8. Back glass (Body sedan)

18.8.1. Partial replacement of a glutinous fringing

GENERAL INFORMATION

Section of consolidation of back glass

1. BACK GLASS
2. CONSOLIDATION

Emphasis of back glass

1. BACK GLASS
2. EMPHASIS OF BACK GLASS

To remove or disconnect

Dismantle of consolidation of back glass (Body sedan)

1. CONSOLIDATION
2. EMPHASIS OF BACK GLASS
3. BACK GLASS

Windscreen dismantle

1. STRING

PERFORMANCE ORDER

1. To remove manually a decorative overlay of back glass. In order to avoid damage of a paint and varnish covering to stick together a sticky tape elements of the Body directly adjacent to back glass.

2. To disconnect electroconducting from a heater of back glass.

3. By means of a knife for removal of a sealant to make an incision the parties and sealant top as it is possible closer to an edge of back glass.

4. The emphasis of back glass located at the bottom edge, fig. Emphasis of back glass. To insert outside a string between glass and the Body and by means of the second mechanic to cut off a glutinous layer on the bottom edge of back glass.

5. Back glass from the car.

To clear

PERFORMANCE ORDER

1. I will eat windows from the remains of all materials.

2. Glass on edge perimeter for the subsequent drawing of preparatory layers.

3. To wipe a windscreen the pure fabric moistened in alcohol.

To establish or attach

Windscreen installation

Drawing on a windscreen of priming structure

1. NEW BRUSH
2. STRUCTURE FOR DRAWING OF THE PRIMING COAT

Drawing of pressurizing structure

PERFORMANCE ORDER

1. By means of a new brush to put on glass edge preparatory layers, using the relevant structures from a repair set. At first it is necessary to put грунтовоч a ny layer from transparent structure, and then – from structure of black color. Priming coats put on perimeter of an edge of glass (from the interior of glass) with a strip in width of 6 mm. To put equal, непрерыв the ny roller of gluing structure on perimeter of glass and over priming coats.
At partial replacement of a fringing the thickness of the roller should make 5 mm.
At complete replacement of a fringing the thickness of the roller should make from 8 to 10 mm.

2. Emphasis of back glass.

3. Back glass in a window aperture by means of the second mechanic. To center glass in a window aperture. Use of rubber suckers can facilitate glass installation, fig. Windscreen installation. To press a glass emphasis in the direction to the car center in order that back glass occupied the correct situation.

4. A molding of back glass, having pressed it by hand.

5. To check a germetichenost of consolidation of back glass, watering it. At detection of a leakage it is necessary to dry glass and in addition to impose pressurizing structure. If it was not possible to eliminate a leak, it is necessary to remove glass and to repeat all installation anew.

Prevention

It is not necessary to direct a strong stream of water on svezhepolozhenny hermetic. The water which has got on a surface of hermetic, promotes polymerization acceleration уретана.