Daewoo Nexia

since 1994 of release

Repair and car operation



Deu Neksiya
+ Maintenance instruction
+ Maintenance
+ Engine
+ 3. Engine (two top camshafts)
+ cooling System
+ Toplevnaya and exhaust systems
+ Electric chain
+ 7. Ignition system
+ 8. Electronic control unit and sensors
+ Transmission
+ 10. Five-speed transmission and main RPO MM5 broadcast
+ 11. Automatic Transmission
+ Steering
+ Running gear
+ 14. Forward suspension bracket
+ 15. Drive of forward wheels
+ 16. Back suspension bracket
+ Brake system
- Body
   18.2. Identification and use of keys
   18.3. Pasted lateral moldings
   18.4. Diagnostics and repair of a leakage of the Body
   18.5. Anticorrosive processing
   + 18.6. Dismantle of consolidations of wind and back glasses
   + 18.7. Windscreen
   + 18.8. Back glass (Body sedan)
   18.9. Glass of a back door (Body hatch-back)
   18.10. Triangular lateral glass
   + 18.11. Elimination of a leakage of consolidations
   + 18.12. Rear-view mirror
   + 18.13. Electroheater of back glass
   + 18.14. Bumpers
   18.15. External ventilating lattice
   18.16. Switch of a forward door
   18.17. Cowl
   18.18. Cowl loops
   18.19. Cowl emphasis
   18.20. Locking device of a cowl
   18.21. Safety latch of a cowl
   18.22. Cable of a latch of a cowl
   18.23. Front grille
   18.24. Forward wing
   + 18.25. Panels of an upholstery of doors
   + 18.26. Equipment of doors (lobbies and back doors)
   + 18.27. Door locks
   + 18.28. Glasses of doors
   18.29. External rear-view mirrors
   18.30. Dismantle and installation of lobbies and back doors
   + 18.31. Back panels of an upholstery (Body hatch-back)
   + 18.32. Upholstery panels (Body sedan)
   18.33. External panel
   18.34. Ventilating valve (Body hatch-back)
   18.35. Hatch of a mouth of a fuel tank
   + 18.36. Opening window leaves (A body a hatch-back)
   + 18.37. Back shelf (Body sedan)
   18.38. Cover of a luggage compartment (Body hatch-back)
   18.39. Overlay of a back wall of a luggage carrier (Body sedan)
   + 18.40. Trunk lid (Body sedan)
   18.41. The back combined lamp
   + 18.42. Back door (Body hatch-back)
   18.43. Roof
   18.44. Ceiling panel
   18.45. Antisolar peaks
   18.46. Plafond of internal lighting
   + 18.47. Panels and salon equipment
   18.48. External longitudinal overlays of a roof
   + 18.49. Ventilating hatch
   + 18.50. Forward seats
   + 18.51. Back seat
+ Heating, ventilation
+ Electric equipment


8128da4b



18.9. Glass of a back door (Body hatch-back)

To remove or disconnect

PERFORMANCE ORDER
1. Internal cord of a sealant of glass of a back door.
2. Electric conducting of a heater of glass.
3. Glass molding. At the subsequent installation of a new molding old it is possible to remove, having wrung out or having cut off it.
4. By means of a knife for removal of a sealant to make an incision consolidation on all perimeter as it is possible closer to a glass edge.
5. Glass of a back door.

To clear

PERFORMANCE ORDER
1. I will eat windows from the remains of all materials.
2. Glass on edge perimeter for the subsequent drawing of preparatory layers.
3. To wipe a windscreen the pure fabric moistened in alcohol.

To establish or attach

PERFORMANCE ORDER
1. By means of a new brush to put on glass edge preparatory layers, using the relevant structures from a repair set. At first it is necessary to put грунтовоч a ny layer from transparent structure, and then – from structure of black color. Priming coats put on perimeter of an edge of glass (from the interior of glass) with a strip in width of 6 mm.
2. A molding on glass. For molding fixing on glass follows, to use a sticky tape (fastens to an external surface of glass). To put on perimeter of a window aperture of a back door the roller of uretanovy hermetic in thickness of 3 mm.
3. Glass in a window aperture of a back door by means of the second mechanic. To center glass in a window doorway. Use of rubber suckers can facilitate glass installation.
4. To check tightness of consolidation of glass of a back door, watering it. At detection of a leakage it is necessary to dry glass and in addition to impose pressurizing structure. If it was not possible to eliminate a leak, it is necessary to remove glass and to repeat all installation anew.
5. Electroconducting of a heater of glass (in the presence of a heater).
6. Internal cord of a sealant of glass.