Daewoo Nexia

since 1994 of release

Repair and car operation

Deu Neksiya
+ Maintenance instruction
+ Maintenance
+ Engine
+ 3. Engine (two top camshafts)
+ cooling System
+ Toplevnaya and exhaust systems
+ Electric chain
+ 7. Ignition system
+ 8. Electronic control unit and sensors
+ Transmission
+ 10. Five-speed transmission and main RPO MM5 broadcast
+ 11. Automatic Transmission
+ Steering
+ Running gear
+ 14. Forward suspension bracket
+ 15. Drive of forward wheels
+ 16. Back suspension bracket
+ Brake system
- Body
   18.2. Identification and use of keys
   18.3. Pasted lateral moldings
   18.4. Diagnostics and repair of a leakage of the Body
   18.5. Anticorrosive processing
   + 18.6. Dismantle of consolidations of wind and back glasses
   + 18.7. Windscreen
   + 18.8. Back glass (Body sedan)
   18.9. Glass of a back door (Body hatch-back)
   18.10. Triangular lateral glass
   + 18.11. Elimination of a leakage of consolidations
   + 18.12. Rear-view mirror
   + 18.13. Electroheater of back glass
   + 18.14. Bumpers
   18.15. External ventilating lattice
   18.16. Switch of a forward door
   18.17. Cowl
   18.18. Cowl loops
   18.19. Cowl emphasis
   18.20. Locking device of a cowl
   18.21. Safety latch of a cowl
   18.22. Cable of a latch of a cowl
   18.23. Front grille
   18.24. Forward wing
   + 18.25. Panels of an upholstery of doors
   + 18.26. Equipment of doors (lobbies and back doors)
   + 18.27. Door locks
   + 18.28. Glasses of doors
   18.29. External rear-view mirrors
   18.30. Dismantle and installation of lobbies and back doors
   + 18.31. Back panels of an upholstery (Body hatch-back)
   + 18.32. Upholstery panels (Body sedan)
   18.33. External panel
   18.34. Ventilating valve (Body hatch-back)
   18.35. Hatch of a mouth of a fuel tank
   + 18.36. Opening window leaves (A body a hatch-back)
   + 18.37. Back shelf (Body sedan)
   18.38. Cover of a luggage compartment (Body hatch-back)
   18.39. Overlay of a back wall of a luggage carrier (Body sedan)
   + 18.40. Trunk lid (Body sedan)
   18.41. The back combined lamp
   + 18.42. Back door (Body hatch-back)
   18.43. Roof
   18.44. Ceiling panel
   18.45. Antisolar peaks
   18.46. Plafond of internal lighting
   + 18.47. Panels and salon equipment
   18.48. External longitudinal overlays of a roof
   + 18.49. Ventilating hatch
   + 18.50. Forward seats
   + 18.51. Back seat
+ Heating, ventilation
+ Electric equipment

18.3. Pasted lateral moldings

GENERAL INFORMATION

Repair of moldings on lateral panels of the Body

Lateral moldings fasten to Body panels, by means of gluing structure. For strong fastening of moldings (old or new) it is necessary, that the surface of panels was pure and free from traces of wax or an oil film, and the temperature of panels was between 21 ° With and 32 ° Page.

Podkleyka of a molding

PERFORMANCE ORDER

1. To wash out the damaged place soap solution and to wipe dry. To wipe a surface of the panel and the contact party of holding a fabric moistened in pure kerosene or alcohol. If the decorative part of a molding departed from the pasted basis (which remained on the Body), the last should not be removed. To clear by means of kerosene (not containing oil) or alcohol of a surface of a prileganiye of the basis of a decorative part of a molding.

2. To paste on the panel directing tape of day of the correct placement of a molding (if necessary).

3. To put on a contact surface of a molding glue and to press a molding to the panel. When using gluing structure of the Loclite 414 brand (or equivalent substitute) to sustain a molding under loading during 30 with or before formation of strong connection.

Molding gluing

PERFORMANCE ORDER

1. To wash out the damaged panel soap solution and to wipe dry. To remove all remains of glue from a surface of the panel and the contact party of a molding by means of pure kerosene (not containing oil) or alcohol.

2. To plan a molding arrangement for Body panels by means of a directing tape. Thus it is necessary to be guided by the provision of the next molding.

3. If the temperature of the panel of the Body does not exceed 21 ° With, it is necessary to heat up the panel by means of reflex lamps or warm air.

4. To put on a molding acrylic gluing structure (for example, ZM brands).

5. To put a molding to the panel and strongly to press.