Daewoo Nexia

since 1994 of release

Repair and car operation



Deu Neksiya
+ Maintenance instruction
+ Maintenance
+ Engine
+ 3. Engine (two top camshafts)
+ cooling System
+ Toplevnaya and exhaust systems
+ Electric chain
+ 7. Ignition system
+ 8. Electronic control unit and sensors
+ Transmission
+ 10. Five-speed transmission and main RPO MM5 broadcast
+ 11. Automatic Transmission
+ Steering
+ Running gear
+ 14. Forward suspension bracket
+ 15. Drive of forward wheels
+ 16. Back suspension bracket
+ Brake system
- Body
   18.2. Identification and use of keys
   18.3. Pasted lateral moldings
   18.4. Diagnostics and repair of a leakage of the Body
   18.5. Anticorrosive processing
   + 18.6. Dismantle of consolidations of wind and back glasses
   + 18.7. Windscreen
   + 18.8. Back glass (Body sedan)
   18.9. Glass of a back door (Body hatch-back)
   18.10. Triangular lateral glass
   + 18.11. Elimination of a leakage of consolidations
   + 18.12. Rear-view mirror
   + 18.13. Electroheater of back glass
   + 18.14. Bumpers
   18.15. External ventilating lattice
   18.16. Switch of a forward door
   18.17. Cowl
   18.18. Cowl loops
   18.19. Cowl emphasis
   18.20. Locking device of a cowl
   18.21. Safety latch of a cowl
   18.22. Cable of a latch of a cowl
   18.23. Front grille
   18.24. Forward wing
   + 18.25. Panels of an upholstery of doors
   + 18.26. Equipment of doors (lobbies and back doors)
   - 18.27. Door locks
      18.27.2. Door locks of lobbies and back doors
      18.27.3. The internal handle of the lock - lobbies and back doors
      18.27.4. Draft of blocking of the lock – lobbies and back doors
      18.27.5. The external handle of the door lock – lobbies and back doors
      - 18.27.6. The lock cylinder – lobbies and back doors
         18.27.6.1. Replacement of the cylinder of the door lock
         18.27.6.2. Assembly of the cylinder of the lock
      18.27.7. Assembly of the door lock
   + 18.28. Glasses of doors
   18.29. External rear-view mirrors
   18.30. Dismantle and installation of lobbies and back doors
   + 18.31. Back panels of an upholstery (Body hatch-back)
   + 18.32. Upholstery panels (Body sedan)
   18.33. External panel
   18.34. Ventilating valve (Body hatch-back)
   18.35. Hatch of a mouth of a fuel tank
   + 18.36. Opening window leaves (A body a hatch-back)
   + 18.37. Back shelf (Body sedan)
   18.38. Cover of a luggage compartment (Body hatch-back)
   18.39. Overlay of a back wall of a luggage carrier (Body sedan)
   + 18.40. Trunk lid (Body sedan)
   18.41. The back combined lamp
   + 18.42. Back door (Body hatch-back)
   18.43. Roof
   18.44. Ceiling panel
   18.45. Antisolar peaks
   18.46. Plafond of internal lighting
   + 18.47. Panels and salon equipment
   18.48. External longitudinal overlays of a roof
   + 18.49. Ventilating hatch
   + 18.50. Forward seats
   + 18.51. Back seat
+ Heating, ventilation
+ Electric equipment


8128da4b



18.27.6.1. Replacement of the cylinder of the door lock

GENERAL INFORMATION

Cylinder of the door lock

1. LEADING RING
2. ARM
3. RETURNABLE SPRING
4. LOCK CYLINDER
5. LOCK CASE
6. THE OPENING FOR WATER REMOVAL

Arrangement of a returnable spring


AND. PAD OF THE RETURNABLE SPRING

1. THE OPENING FOR MOISTURE REMOVAL

Locking plates of the door lock

1. NEST OF THE SPRING OF THE PLATE
2. FIRST CUT OF THE CYLINDER OF THE LOCK
3. LOCKING PLATE
As spare parts the sets of details intended for replacement of any locks of the car are delivered. Locking plates for all locks are executed an identical form except for the sizes of a through cut. Four standard sizes of locking plates which provide various combinations of confidential codes of locks are used. Each standard size of plates has numerical marking from 1 to 4. Marking is put on the party of each plate. The small beard of a key of one-times but cooperates with 10 locking plates.

Depending on a combination of standard sizes of the set of locking plates established in the cylinder the small beard of a key has this or that profile.