Daewoo Nexia

since 1994 of release

Repair and car operation



Deu Neksiya
+ Maintenance instruction
+ Maintenance
+ Engine
+ 3. Engine (two top camshafts)
+ cooling System
+ Toplevnaya and exhaust systems
+ Electric chain
+ 7. Ignition system
+ 8. Electronic control unit and sensors
+ Transmission
+ 10. Five-speed transmission and main RPO MM5 broadcast
+ 11. Automatic Transmission
+ Steering
+ Running gear
+ 14. Forward suspension bracket
+ 15. Drive of forward wheels
+ 16. Back suspension bracket
+ Brake system
- Body
   18.2. Identification and use of keys
   18.3. Pasted lateral moldings
   18.4. Diagnostics and repair of a leakage of the Body
   18.5. Anticorrosive processing
   + 18.6. Dismantle of consolidations of wind and back glasses
   + 18.7. Windscreen
   + 18.8. Back glass (Body sedan)
   18.9. Glass of a back door (Body hatch-back)
   18.10. Triangular lateral glass
   + 18.11. Elimination of a leakage of consolidations
   + 18.12. Rear-view mirror
   + 18.13. Electroheater of back glass
   + 18.14. Bumpers
   18.15. External ventilating lattice
   18.16. Switch of a forward door
   18.17. Cowl
   18.18. Cowl loops
   18.19. Cowl emphasis
   18.20. Locking device of a cowl
   18.21. Safety latch of a cowl
   18.22. Cable of a latch of a cowl
   18.23. Front grille
   18.24. Forward wing
   + 18.25. Panels of an upholstery of doors
   + 18.26. Equipment of doors (lobbies and back doors)
   + 18.27. Door locks
   + 18.28. Glasses of doors
   18.29. External rear-view mirrors
   18.30. Dismantle and installation of lobbies and back doors
   + 18.31. Back panels of an upholstery (Body hatch-back)
   + 18.32. Upholstery panels (Body sedan)
   18.33. External panel
   18.34. Ventilating valve (Body hatch-back)
   18.35. Hatch of a mouth of a fuel tank
   + 18.36. Opening window leaves (A body a hatch-back)
   + 18.37. Back shelf (Body sedan)
   18.38. Cover of a luggage compartment (Body hatch-back)
   18.39. Overlay of a back wall of a luggage carrier (Body sedan)
   + 18.40. Trunk lid (Body sedan)
   18.41. The back combined lamp
   + 18.42. Back door (Body hatch-back)
   18.43. Roof
   18.44. Ceiling panel
   18.45. Antisolar peaks
   18.46. Plafond of internal lighting
   + 18.47. Panels and salon equipment
   18.48. External longitudinal overlays of a roof
   - 18.49. Ventilating hatch
      18.49.1. Sharnirny loop
      18.49.2. Glass panel
      18.49.3. Fringing
      18.49.4. Hatch lock
      18.49.5. Sealant
   + 18.50. Forward seats
   + 18.51. Back seat
+ Heating, ventilation
+ Electric equipment


8128da4b



18.49.5. Sealant

GENERAL INFORMATION

The sealant of the hatch represents the closed profilirovanny ring. The sealant is established in a groove on aperture perimeter on glue.

To remove or disconnect

PERFORMANCE ORDER
1. The glass panel from a hatch frame.
2. To cut off glutinous connection of a sealant on perimeter of a groove and to dismantle consolidation.
Prevention

For acceleration of dismantle of consolidation it is recommended to heat up consolidation by a stream of hot air or to moisten glutinous connection by solvent for glue.


3. After removal of consolidation to clear a groove of the glue remains by means of solvent.

To establish or attach

PERFORMANCE ORDER
1. To paste a protective tape on perimeter of an aperture of the hatch.
2. To put a layer of glue of brand 3М Windo-Weid Primer (black color) on horizontal and vertical surfaces of a groove. Let's to glue dry up within 10–15 minutes.
3. To clear. a consolidation surface by means of suitable solvent.
4. To grease contact surfaces with a layer of glue of brand 3М Windo-Weid Primer (black color) and let's to glue dry up within 10–15 minutes.
5. Being guided by a cross-section seam of a sealant, to put a label with a sticky tape in the middle of the opposite side. Condense a tel it is necessary to mount so that the cross-section seam was in the middle of the back party of an aperture. To put a glue 3М Weatheistrip Adhesive layer on groove surfaces for consolidation installation on internal perimeter of an aperture of the hatch.
6. By means of a brush to put glue on contact surfaces of consolidation.
7. After glue becomes sticky, to level the provision of a sealant on a seam and labels from a sticky tape and to insert a sealant into a groove. The cross-section seam should be in the middle of the back party of an aperture over the handle of a lock of the hatch.
8. By means of a syringe to put a glue layer between outer side of consolidation and aperture edge in a roof.
9. Let's dry out to glue within 8 hours before to mount the hatch and to check a sealant on tightness. Before installation of the glass hatch to put on a sealant silicone greasing.
10. To establish the glass panel on a hatch frame.