Daewoo Nexia

since 1994 of release

Repair and car operation



Deu Neksiya
+ Maintenance instruction
+ Maintenance
+ Engine
+ 3. Engine (two top camshafts)
+ cooling System
+ Toplevnaya and exhaust systems
+ Electric chain
+ 7. Ignition system
+ 8. Electronic control unit and sensors
+ Transmission
+ 10. Five-speed transmission and main RPO MM5 broadcast
+ 11. Automatic Transmission
+ Steering
+ Running gear
+ 14. Forward suspension bracket
+ 15. Drive of forward wheels
+ 16. Back suspension bracket
+ Brake system
- Body
   18.2. Identification and use of keys
   18.3. Pasted lateral moldings
   18.4. Diagnostics and repair of a leakage of the Body
   18.5. Anticorrosive processing
   + 18.6. Dismantle of consolidations of wind and back glasses
   + 18.7. Windscreen
   + 18.8. Back glass (Body sedan)
   18.9. Glass of a back door (Body hatch-back)
   18.10. Triangular lateral glass
   + 18.11. Elimination of a leakage of consolidations
   + 18.12. Rear-view mirror
   + 18.13. Electroheater of back glass
   + 18.14. Bumpers
   18.15. External ventilating lattice
   18.16. Switch of a forward door
   18.17. Cowl
   18.18. Cowl loops
   18.19. Cowl emphasis
   18.20. Locking device of a cowl
   18.21. Safety latch of a cowl
   18.22. Cable of a latch of a cowl
   18.23. Front grille
   18.24. Forward wing
   + 18.25. Panels of an upholstery of doors
   + 18.26. Equipment of doors (lobbies and back doors)
   + 18.27. Door locks
   + 18.28. Glasses of doors
   18.29. External rear-view mirrors
   18.30. Dismantle and installation of lobbies and back doors
   + 18.31. Back panels of an upholstery (Body hatch-back)
   + 18.32. Upholstery panels (Body sedan)
   18.33. External panel
   18.34. Ventilating valve (Body hatch-back)
   18.35. Hatch of a mouth of a fuel tank
   + 18.36. Opening window leaves (A body a hatch-back)
   + 18.37. Back shelf (Body sedan)
   18.38. Cover of a luggage compartment (Body hatch-back)
   18.39. Overlay of a back wall of a luggage carrier (Body sedan)
   + 18.40. Trunk lid (Body sedan)
   18.41. The back combined lamp
   - 18.42. Back door (Body hatch-back)
      18.42.1. Gas shock-absorbers
      + 18.42.2. Lock
      18.42.3. Assembly of the door lock
      18.42.4. Loops
      18.42.5. Sealant
      18.42.6. Central top stoplight
      18.42.7. Back spoiler
   18.43. Roof
   18.44. Ceiling panel
   18.45. Antisolar peaks
   18.46. Plafond of internal lighting
   + 18.47. Panels and salon equipment
   18.48. External longitudinal overlays of a roof
   + 18.49. Ventilating hatch
   + 18.50. Forward seats
   + 18.51. Back seat
+ Heating, ventilation
+ Electric equipment


8128da4b



18.42.1. Gas shock-absorbers

GENERAL INFORMATION

Gas shock-absorbers of a back door

1. GAS SHOCK-ABSORBER
2. EMPHASIS
3. CLIP
4. THE SPHERICAL FINGER OF THE HINGE ON THE BACK DOOR
5. SPHERICAL FINGER of ON the HINGE Body

Gas shock-absorbers are intended for simplification of lifting of a back door. Shock-absorbers are fixed on a back door and the Body by means of the spherical hinges consisting of spherical fingers and tips. For fixing of spherical fingers clips serve.

To remove or disconnect

PERFORMANCE ORDER
1. To establish an emphasis under a back open door.
2. Clips of spherical hinges and shock-absorbers from a back door.
3. Clips of spherical hinges and shock-absorbers from a car Body.

To establish or attach

PERFORMANCE ORDER
1. Gas shock-absorbers to a car Body to fix hinges clips.
2. Gas shock-absorbers to a back door to fix hinges clips.
3. To check keeping of a back door by gas shock-absorbers in completely open situation.
Prevention

At low temperature of air (below–29 ° C) pressure of gas in the shock-absorber decreases. It leads to reduction of efforts on a shock-absorber rod when fixing a back door in open situation. Temperature increase normalizes operation of gas shock-absorbers.