Daewoo Nexia

since 1994 of release

Repair and car operation


Deu Neksiya
+ Maintenance instruction
+ Maintenance
+ Engine
+ 3. Engine (two top camshafts)
+ cooling System
+ Toplevnaya and exhaust systems
+ Electric chain
+ 7. Ignition system
+ 8. Electronic control unit and sensors
+ Transmission
+ 10. Five-speed transmission and main RPO MM5 broadcast
+ 11. Automatic Transmission
+ Steering
+ Running gear
+ 14. Forward suspension bracket
+ 15. Drive of forward wheels
+ 16. Back suspension bracket
+ Brake system
- Body
   18.2. Identification and use of keys
   18.3. Pasted lateral moldings
   18.4. Diagnostics and repair of a leakage of the Body
   18.5. Anticorrosive processing
   + 18.6. Dismantle of consolidations of wind and back glasses
   + 18.7. Windscreen
   + 18.8. Back glass (Body sedan)
   18.9. Glass of a back door (Body hatch-back)
   18.10. Triangular lateral glass
   + 18.11. Elimination of a leakage of consolidations
   + 18.12. Rear-view mirror
   + 18.13. Electroheater of back glass
   + 18.14. Bumpers
   18.15. External ventilating lattice
   18.16. Switch of a forward door
   18.17. Cowl
   18.18. Cowl loops
   18.19. Cowl emphasis
   18.20. Locking device of a cowl
   18.21. Safety latch of a cowl
   18.22. Cable of a latch of a cowl
   18.23. Front grille
   18.24. Forward wing
   + 18.25. Panels of an upholstery of doors
   + 18.26. Equipment of doors (lobbies and back doors)
   + 18.27. Door locks
   + 18.28. Glasses of doors
   18.29. External rear-view mirrors
   18.30. Dismantle and installation of lobbies and back doors
   + 18.31. Back panels of an upholstery (Body hatch-back)
   + 18.32. Upholstery panels (Body sedan)
   18.33. External panel
   18.34. Ventilating valve (Body hatch-back)
   18.35. Hatch of a mouth of a fuel tank
   + 18.36. Opening window leaves (A body a hatch-back)
   + 18.37. Back shelf (Body sedan)
   18.38. Cover of a luggage compartment (Body hatch-back)
   18.39. Overlay of a back wall of a luggage carrier (Body sedan)
   - 18.40. Trunk lid (Body sedan)
      18.40.1. Torsiona of a trunk lid
      - 18.40.2. Trunk lid lock
         18.40.2.1. Locking loop of the lock
         18.40.2.2. Lock cylinder
      18.40.3. Assembly of the door lock
      18.40.4. Sealant
   18.41. The back combined lamp
   + 18.42. Back door (Body hatch-back)
   18.43. Roof
   18.44. Ceiling panel
   18.45. Antisolar peaks
   18.46. Plafond of internal lighting
   + 18.47. Panels and salon equipment
   18.48. External longitudinal overlays of a roof
   + 18.49. Ventilating hatch
   + 18.50. Forward seats
   + 18.51. Back seat
+ Heating, ventilation
+ Electric equipment


8128da4b



18.40.2.2. Lock cylinder
GENERAL INFORMATION

Lock cylinder assembled

 
1. NUT (2 PIECES)
2. LOCK CYLINDER ASSEMBLED
3. DRAUGHT
4. THE RING WITH THE LEADING LEAD
5. ARM
6. RETURNABLE SPRING
7. LOCK CYLINDER
8. LOCK CASE

Lock cylinder

1. NESTS OF SPRINGS
2. THE FIRST CUT FOR THE LOCKING PLATE (REMAINS EMPTY)
3. LOCKING PLATE

To remove or disconnect

PERFORMANCE ORDER
1. To unscrew two nuts of a kropleniye of the cylinder of the lock.
2. To disconnect draft from the cylinder of the lock and to remove it from a trunk lid.

To establish or attach

PERFORMANCE ORDER
1. The lock cylinder in a trunk lid, having attached to the cylinder draft.
2. Two nuts of fastening of the cylinder of the lock to a trunk lid.
3. To insert springs of plates and locking plates into the corresponding openings and cuts of the cylinder of the lock. Thus it is necessary to be guided by a key code.
Prevention

Not to establish a spring and a plate in the first cut of the cylinder. At installation of springs and locking plates in the cylinder of the lock it is necessary to grease all details with a thin layer of konsistentny greasing.

4. For check of correctness of assembly to insert into the lock cylinder a key. If all plates act from the cylinder, assembly is made correctly.