Daewoo Nexia

since 1994 of release

Repair and car operation



Deu Neksiya
+ Maintenance instruction
+ Maintenance
+ Engine
+ 3. Engine (two top camshafts)
+ cooling System
+ Toplevnaya and exhaust systems
+ Electric chain
+ 7. Ignition system
+ 8. Electronic control unit and sensors
+ Transmission
+ 10. Five-speed transmission and main RPO MM5 broadcast
+ 11. Automatic Transmission
+ Steering
+ Running gear
+ 14. Forward suspension bracket
+ 15. Drive of forward wheels
+ 16. Back suspension bracket
+ Brake system
- Body
   18.2. Identification and use of keys
   18.3. Pasted lateral moldings
   18.4. Diagnostics and repair of a leakage of the Body
   18.5. Anticorrosive processing
   + 18.6. Dismantle of consolidations of wind and back glasses
   + 18.7. Windscreen
   + 18.8. Back glass (Body sedan)
   18.9. Glass of a back door (Body hatch-back)
   18.10. Triangular lateral glass
   + 18.11. Elimination of a leakage of consolidations
   - 18.12. Rear-view mirror
      18.12.1. Installation of an arm of a rear-view mirror
      18.12.2. Rear-view mirror adjustment
   + 18.13. Electroheater of back glass
   + 18.14. Bumpers
   18.15. External ventilating lattice
   18.16. Switch of a forward door
   18.17. Cowl
   18.18. Cowl loops
   18.19. Cowl emphasis
   18.20. Locking device of a cowl
   18.21. Safety latch of a cowl
   18.22. Cable of a latch of a cowl
   18.23. Front grille
   18.24. Forward wing
   + 18.25. Panels of an upholstery of doors
   + 18.26. Equipment of doors (lobbies and back doors)
   + 18.27. Door locks
   + 18.28. Glasses of doors
   18.29. External rear-view mirrors
   18.30. Dismantle and installation of lobbies and back doors
   + 18.31. Back panels of an upholstery (Body hatch-back)
   + 18.32. Upholstery panels (Body sedan)
   18.33. External panel
   18.34. Ventilating valve (Body hatch-back)
   18.35. Hatch of a mouth of a fuel tank
   + 18.36. Opening window leaves (A body a hatch-back)
   + 18.37. Back shelf (Body sedan)
   18.38. Cover of a luggage compartment (Body hatch-back)
   18.39. Overlay of a back wall of a luggage carrier (Body sedan)
   + 18.40. Trunk lid (Body sedan)
   18.41. The back combined lamp
   + 18.42. Back door (Body hatch-back)
   18.43. Roof
   18.44. Ceiling panel
   18.45. Antisolar peaks
   18.46. Plafond of internal lighting
   + 18.47. Panels and salon equipment
   18.48. External longitudinal overlays of a roof
   + 18.49. Ventilating hatch
   + 18.50. Forward seats
   + 18.51. Back seat
+ Heating, ventilation
+ Electric equipment


8128da4b



18.12.1. Installation of an arm of a rear-view mirror

GENERAL INFORMATION

Rear-view mirror

1. SCREW of ADJUSTMENT of the MIRROR (3 mm)
2. SCREW of FASTENING of the MIRROR (2 mm)

Windscreen marking for arm installation rear-view mirrors (beginning)


AND. THE SIZE A IS EQUAL 110 MM (FROM THE TOP EDGE OF GLASS TO THE BOTTOM EDGE OF THE ARM OF THE MIRROR)

Windscreen marking for arm installation rear-view mirrors (termination)

1. KARANDASH-STEKLOGRAF OR IT IS SMALL
2. MARKING LINES ON THE EXTERNAL SURFACE OF THE WINDSCREEN. PROVISION OF THE ARM OF THE MIRROR
3. THE CIRCULAR LINE ON THE EXTERNAL SURFACE OF THE GLASS, LIMITING THE ZONE OF PURIFICATION OF GLASS
4. CENTRAL LINE

PERFORMANCE ORDER
1. To note the demanded distance down from the top edge of glass to a place where the arm, fig. will be established. A windscreen marking for arm installation rear-view mirrors (beginning). To note the provision of an arm on the outer side of a windscreen by means of a steklograf or a piece of chalk. To put the circular line of big diameter around песта arm installations, fig. A windscreen marking for arm installation rear-view mirrors (termination).
2. To clear an internal surface of a windscreen by means of a household cleaner and a paper towel or by means of a cleaner for glasses. To wipe glass a paper towel dry. After that to wash out glass from traces of cleaners by means of the paper towel moistened in alcohol.
3. To process a surface of a prileganiye of an arm (if it new) a skin with granularity 320 or 360. In case of use of the dismantled arm it is necessary to remove completely with поверхностй prileganiye all traces of old glue.
After grinding to wash out a surface of a prileganiye of an arm the paper towel moistened in alcohol, and let's to it dry out.
To prepare a glass and arm surface for pasting, following instructions of firm manufacturer of a repair set.
To place an arm on a windscreen according to a marking and strongly to press it on 30-60 page. 5 minutes later to remove surpluses of glue by means of a towel moistened in alcohol, or a cleaner for glasses.

To establish or attach

PERFORMANCE ORDER
1. A rear-view mirror on an arm.
2. To fix a mirror by means of the 2-millimetric screw, fig. Rear-view mirror.