Daewoo Nexia

since 1994 of release

Repair and car operation

Deu Neksiya
+ Maintenance instruction
+ Maintenance
+ Engine
+ 3. Engine (two top camshafts)
+ cooling System
+ Toplevnaya and exhaust systems
+ Electric chain
+ 7. Ignition system
+ 8. Electronic control unit and sensors
+ Transmission
+ 10. Five-speed transmission and main RPO MM5 broadcast
+ 11. Automatic Transmission
+ Steering
+ Running gear
- 14. Forward suspension bracket
   14.2. General description
   14.3. Check of size of forces of a friction in a suspension bracket
   14.4. Check of a condition of bearing support and spherical hinges
   14.5. Stabilizer
   14.6. A rack assembled with a bearing support
   14.7. Bottom lever
   14.8. Spherical hinge
   14.9. Nave and wheel bearing
   14.10. Top support
   14.11. Springs
   14.12. Shock-absorber
   14.13. Plugs of hinges of the bottom lever
+ 15. Drive of forward wheels
+ 16. Back suspension bracket
+ Brake system
+ Body
+ Heating, ventilation
+ Electric equipment

14.9. Nave and wheel bearing

GENERAL INFORMATION

Fastening of a telescopic rack to the Body

36. PROTECTIVE COVER OF THE TOP SUPPORT
37. NUT (MOMENT OF THE INHALING OF 30 NANOMETERS)
39. TOP (BEARING) SUPPORT OF THE RACK

Spring clamp

AND. BACK HANDLE
CENTURY. FORWARD LOOPS
PAGE. CLAMPS

1. SPRING CLAMP

Bearing support of a nave

33. BEARING SUPPORT OF THE RACK
47. THE FLUTE FOR THE SPRING RING (INTERNAL)
48. BEARING

49. THE FLUTE FOR THE SPRING RING (EXTERNAL)
50. NAVE
61. BEARING RING
62. SEMI-AXIS

Adjusting screw of a brake disk

To remove or disconnect

Dismantle of the spherical hinge of the bottom lever

6. SPHERICAL HINGE OF THE BOTTOM LEVER
13. BOTTOM LEVER
57. BRACKET OF THE DISK BRAKE

Semi-axis dismantle from a nave

AND. NUT
CENTURY. BOLT
PAGE. PERSISTENT BEARING

33. THE RACK WITH THE BEARING SUPPORT

PERFORMANCE ORDER

1. To release two nuts of the 37th fastening of the top support of a rack.

2. To release bolts of fastening of forward wheels. To take out шплинт 54, to unscrew a nut of 55 semi-axes and to remove a washer 53.

3. To lift the car.

4. To bring basic racks under the car.

5. To lower it is a little car so that he leaned on racks, but not on the bottom levers.

6. Forward wheels.

Prevention

To track after dismantle of nuts of a semi-axis did not leave internal mobile hinges. It will lead to dismantling of hinges. Probably also damage of hinges. During work in a zone of an arrangement of hinges of semi-axes it is necessary to use the protective covers which are put on rubber antisplash consolidations of hinges. Otherwise damage of details or consolidations of hinges and an exit of hinges out of operation is possible.

7. A bracket of the 57th brake from a bearing support. After dismantle it is necessary to fix a bracket not to damage brake hoses.

8. Screw 56.

9. Brake disk 52.

10. Nuts of spherical hinges of rotary levers.

Prevention

For dismantle of external spherical hinges of a steering trapeze use stripper KM-507В.

11. Spring clamp of 1 nut 2.

11а. To raise a back handle of a clamp and to take out it for forward loops.

12. To unscrew a nut 2.

13. By means of stripper KM-507В to take out a finger of the spherical hinge from an opening of an arm of a bearing support.

Prevention

When using stripper KM-507В for dismantle of spherical hinges it is not necessary to pay attention to an inscription "This party to a wheel", vyshtampovanny on the adaptation.

14. To disconnect a semi-axis from a nave.

15. To fix a semi-axis.

16. To lower the car to turn on and remove two nuts 37 with washers 38.

17. Telescopic rack 33 assembled.

Prevention

At dismantle and further works with springs of racks not to allow chips or scratches of a covering of rounds of springs.

To disassemble

Dismantle of a nave of a wheel

AND. NUT
CENTURY. BOLT
PAGE. BEARING

33. BEARING SUPPORT OF THE TELESCOPIC RACK
50. NAVE

Dismantle of an internal ring of the bearing

50. NAVE
63. INTERNAL RING OF THE BEARING

Dismantle and bearing installation

AND. BOLT
CENTURY. NUT
PAGE. BEARING

33. BEARING SUPPORT OF THE RACK
47. SPRING RING. TO REMOVE BEFORE DEMONTAZHEM OF THE BEARING. TO ESTABLISH INTO PLACE AFTER INSTALLATION OF THE NAVE 50.
48. BEARING
49. SPRING RING. TO REMOVE BEFORE DEMONTAZHEM OF THE BEARING. TO ESTABLISH INTO PLACE BEFORE INSTALLATION
BEARING.

PERFORMANCE ORDER

1. To take out a nave 50 of the bearing 48.

2. By means of stripper KM-161А to remove an internal ring of 61 bearings from a nave 50.

Prevention

Before demontazhy the bearing 48 from a support 33 it is necessary to remove spring rings 47 and 49.

3. To take out the bearing 48. The dismantled bearing is not subject to further use.

To clear

PERFORMANCE ORDER

Landing opening in a bearing support 33.

To collect

Installation of spring rings

47. SPRING RING (INTERNAL)
48. BEARING
49. SPRING RING (EXTERNAL)
50. NAVE

PERFORMANCE ORDER

1. To establish in a flute a spring ring 49 (before bearing installation). The spring ring 47 is established in a flute after installation of a nave 50.

2. To insert the bearing.

3. To establish a nave 50 in the bearing 48.

4. To establish into place a spring ring 47.

To establish or attach

Installation of a nave of a wheel

AND. TO ESTABLISH INTO PLACE THE INTERNAL SPRING RING AFTER NAVE INSTALLATION
CENTURY. NUT
PAGE. BEARING
D. BOLT

33. BEARING SUPPORT OF THE RACK
50. NAVE

PERFORMANCE ORDER

1. To remove a protective cover of consolidations of hinges.

2. To insert a semi-axis into a shlitsevy opening of a nave 50. To establish on a semi-axis shaft a washer and a new nut. Before assembly to check availability of greasing in semi-axis hinges. If necessary to add the corresponding greasing. Not to tighten a nut 55 before installation of a wheel and car lowering on a floor.

3. The spherical hinge on a bearing support 33.

4. Nut 2.

5. The spherical hinge of steering draft on the rotary lever of a rack 33. To tighten a nut of the spherical hinge of steering draft the moment of 60 Nanometers. To fix a nut shplinty (if it is provided). To tighten a nut of fastening of the spherical hinge of the bottom lever the moment of 70 Nanometers. To establish a spring clamp.

6. Brake disk and adjusting screw. To tighten the adjusting screw of a brake disk the moment of 4 Nanometers.

7. Bracket of a disk brake.

8. Wheel.

9. To raise it is a little car.

10. To remove basic racks.

11. To lower the car.

12. To tighten bolts of fastening of a wheel in a cross order the moment of 90 Nanometers.

13. To tighten a nut of fastening of a semi-axis the moment of 100 Nanometers (previously). To use only a new koronchaty nut.

14. To release a nut of fastening of a semi-axis and to tighten it the moment of 20 Nanometers.

15. To tighten a nut of fastening of a semi-axis on 1/4 turns. If the cut of a nut does not coincide with an opening under шплинт in a semi-axis shaft, the additional tightening of a nut is forbidden. In this case it is necessary to release a nut and to repeat all operations at first.