Deu Neksiya
+ Maintenance instruction
+ Maintenance
+ Engine
+ 3. Engine (two top camshafts)
+ cooling System
+ Toplevnaya and exhaust systems
+ Electric chain
+ 7. Ignition system
+ 8. Electronic control unit and sensors
+ Transmission
+ 10. Five-speed transmission and main RPO MM5 broadcast
+ 11. Automatic Transmission
+ Steering
+ Running gear
- 14. Forward suspension bracket
14.2. General description
14.3. Check of size of forces of a friction in a suspension bracket
14.4. Check of a condition of bearing support and spherical hinges
14.5. Stabilizer
14.6. A rack assembled with a bearing support
14.7. Bottom lever
14.8. Spherical hinge
14.9. Nave and wheel bearing
14.10. Top support
14.11. Springs
14.12. Shock-absorber
14.13. Plugs of hinges of the bottom lever
+ 15. Drive of forward wheels
+ 16. Back suspension bracket
+ Brake system
+ Body
+ Heating, ventilation
+ Electric equipment
|
To remove or disconnect
| PERFORMANCE ORDER |
| 1. To release bolts of fastening of forward wheels. |
| 2. To lift the car. |
| 3. To bring basic racks under the car. |
| 4. To lower it is a little car so that he leaned on racks, but not on the bottom levers. |
| 5. Forward wheels. |
6. The stabilizer from the bottom lever (a detail 8, 9, 10, 18, 19, 20, 21, 22, 28, 29. 30).
Prevention
To track that the semi-axis did not leave the internal mobile hinge. It will lead to hinge dismantling. Probably also hinge damage. During work in a zone of an arrangement of hinges of semi-axes it is necessary to use the protective covers which are put on rubber antisplash consolidations of hinges. Otherwise damage of details or consolidations of hinges and an exit of hinges out of operation is possible.
|
| 7. Spring clamp 1 and nut 2 spherical hinges 6. |
| 8. Spherical hinge 6. When using stripper KM-507В for dismantle of spherical hinges it is not necessary to pay attention to an inscription "This party to a wheel", vyshtampovanny on the adaptation. |
| 9. Bolts 3, 11th fastenings of the bottom lever. |
| 10. Bottom lever 13. |
|
To establish or attach
Fastening of the bottom lever
|
|
3. BOLT. To USE NEW BOLTS. ON the CARVING to PUT HERMETIC. MOMENT of the INHALING of 70 Nanometers.
11. BOLT. TO USE THE NEW BOLT. AT FIRST TO ESTABLISH
FORWARD BOLT. MOMENT of the INHALING of 140 Nanometers. |
| PERFORMANCE ORDER |
| 1. Bolt 11 and washer 12. |
2. Bolts of 3 fastenings of the back end of the lever 13.
Prevention
Nuts of fastening of the bottom lever should not be thus tightened.
|
| 3. The stabilizer to the bottom lever (to a detail 8, 9, 10, 18, 19, 20, 21, 22, 28, 29, 30). |
| 4. The spherical hinge 6 on a rack 33 and a nut 2. |
5. To raise the car so that he leaned on the bottom levers.
Prevention
The inhaling of bolts and nuts of fastening of the bottom levers should be made at a car opiraniye on the bottom levers in the static provision of a suspension bracket which corresponds to the equipped mass of the car.
|
| 6. To tighten a nut of fastening of the stabilizer the moment of 17 Nanometers. |
| 7. To tighten bolts of 3 fastenings of the back end of the lever the moment of 70 Nanometers. |
| 8. To tighten a forward bolt of the 11th fastening of the lever the moment of 140 Nanometers. |
| 9. To tighten a nut 2 spherical hinges the moment of 70 Nanometers. |
| 10. A nut 2 and a spring clamp on a finger of the spherical hinge. |
| 11. To remove a protective casing of consolidations of hinges of a semi-axis. |
| 12. Wheel. |
| 13. To raise it is a little car. |
| 14. To remove basic racks. |
| 15. To lower the car. |
| 16. To tighten bolts of fastening of a wheel in a cross order the moment of 90 Nanometers. |
|
|
|
