Daewoo Nexia

since 1994 of release

Repair and car operation

Deu Neksiya
+ Maintenance instruction
+ Maintenance
+ Engine
+ 3. Engine (two top camshafts)
+ cooling System
+ Toplevnaya and exhaust systems
+ Electric chain
+ 7. Ignition system
+ 8. Electronic control unit and sensors
+ Transmission
+ 10. Five-speed transmission and main RPO MM5 broadcast
+ 11. Automatic Transmission
+ Steering
+ Running gear
- 14. Forward suspension bracket
   14.2. General description
   14.3. Check of size of forces of a friction in a suspension bracket
   14.4. Check of a condition of bearing support and spherical hinges
   14.5. Stabilizer
   14.6. A rack assembled with a bearing support
   14.7. Bottom lever
   14.8. Spherical hinge
   14.9. Nave and wheel bearing
   14.10. Top support
   14.11. Springs
   14.12. Shock-absorber
   14.13. Plugs of hinges of the bottom lever
+ 15. Drive of forward wheels
+ 16. Back suspension bracket
+ Brake system
+ Body
+ Heating, ventilation
+ Electric equipment

14.6. A rack assembled with a bearing support

GENERAL INFORMATION

Fastening of a telescopic rack to the Body

36. PROTECTIVE COVER OF THE TOP SUPPORT
37. NUT (MOMENT OF THE INHALING OF 30 NANOMETERS)
39. TOP (BEARING) SUPPORT OF THE RACK

Spring clamp

AND. BACK HANDLE
CENTURY. FORWARD LOOPS
PAGE. CLAMPS

1. SPRING CLAMP

To remove or disconnect

Dismantle of the hinge of steering draft

33. THE RACK WITH THE BEARING SUPPORT
59. TIP OF STEERING DRAUGHT

Dismantle of the spherical hinge of the bottom lever

6. SPHERICAL HINGE OF THE BOTTOM LEVER
13. BOTTOM LEVER
57. BRACKET OF THE DISK BRAKE

Semi-axis dismantle from a nave

AND. NUT
CENTURY. BOLT
PAGE. PERSISTENT BEARING

33. THE RACK WITH THE BEARING SUPPORT

PERFORMANCE ORDER

1. To release two nuts of the 37th fastening of the top support of a rack.

2. To release bolts of fastening of forward wheels. To take out шплинт 54, to unscrew a nut of 55 semi-axes and to remove a washer 53.

3. To lift the car.

4. To bring basic racks under the car.

5. To lower it is a little car so that he leaned on racks, but not on the bottom levers.

6. Forward wheels.

Prevention

To track after dismantle of nuts of a semi-axis did not leave internal mobile hinges. It will lead to dismantling of hinges. Probably also damage of hinges. During work in a zone of an arrangement of hinges of semi-axes it is necessary to use the protective covers which are put on rubber antisplash consolidations of hinges. Otherwise damage of details or consolidations of hinges and an exit of hinges out of operation is possible.

7. A bracket of the 57th brake from a bearing support. After dismantle follows зафиксиро вать a bracket not to damage brake hoses.

8. Screw 56.

9. Brake disk 52.

10. Nuts of spherical hinges of rotary levers.

Prevention

For dismantle of external spherical hinges of a steering trapeze use stripper KM-507В.

11. Spring clamp of 1 nut 2.

11а. To raise a back handle of a clamp and to take out it for forward loops.

12. To unscrew a nut 2.

13. By means of stripper KM-507В to take out a finger of the spherical hinge from an opening of an arm of a bearing support.

Prevention

When using stripper KM-507В for dismantle of spherical hinges it is not necessary to pay attention to an inscription "This party to a wheel", vyshtampovanny on the adaptation.

14. To disconnect a semi-axis from a nave.

15. To fix a semi-axis.

16. To lower the car to turn on and remove two nuts 37 with washers 38.

17. Telescopic rack 33 assembled.

Prevention

At dismantle and further works with springs of racks not to allow chips or scratches of a covering of rounds of springs.

To establish or attach

PERFORMANCE ORDER

1. A telescopic rack 33 in collecting and two nuts of the 37th fastening are resistant to the Body.

2. To tighten nuts of fastening of a rack to the Body the moment of 25 Nanometers.

3. To remove the protective covers which have been put on rubber antisplash consolidations of hinges.

4. To insert a semi-axis shaft into a shlitsevy opening of a nave 51. To establish a washer 53 and to screw a new nut 55. Before assembly to check availability of greasing in semi-axis hinges. If necessary to add the corresponding greasing. Not to tighten a nut 55 before installation of a wheel and car lowering on a floor.

5. The spherical hinge on a bearing support and a nut 2. To tighten a nut of fastening of the spherical hinge the moment of 70 Nanometers.

6. Spring clamp 1.

7. Spherical hinge of steering bent for to the lever of a rack 33. To tighten a nut of fastening of the spherical hinge of steering bent for to the rack lever the moment of 60 Nanometers.

8. Brake disk 52 and screw 56. To tighten the screw of fastening of a disk to a nave the moment of 4 Nanometers.

9. A bracket 57 disk brakes on a rack 33.

10. Wheel.

11. To raise it is a little car.

12. To remove basic racks.

13. To lower the car.

14. To tighten bolts of fastening of a wheel in a cross order the moment of 90 Nanometers.

15. To tighten a koronchaty nut of the 55th fastening of a semi-axis the moment of 100 Nanometers. (To use a new nut).

16. To release a nut 55 and then finally to tighten it the moment of 20 Nanometers.

17. At discrepancy of a cut of a nut with an opening in a semi-axis shaft for шплинта a few to unscrew a nut 55 and again to tighten the specified moment. It is forbidden to increase the inhaling moment for ensuring coincidence of a cut of a nut with an opening for installation шплинта 54.