Daewoo Nexia

since 1994 of release

Repair and car operation



Deu Neksiya
+ Maintenance instruction
+ Maintenance
+ Engine
+ 3. Engine (two top camshafts)
+ cooling System
+ Toplevnaya and exhaust systems
+ Electric chain
+ 7. Ignition system
+ 8. Electronic control unit and sensors
+ Transmission
+ 10. Five-speed transmission and main RPO MM5 broadcast
+ 11. Automatic Transmission
+ Steering
+ Running gear
- 14. Forward suspension bracket
   14.2. General description
   14.3. Check of size of forces of a friction in a suspension bracket
   14.4. Check of a condition of bearing support and spherical hinges
   14.5. Stabilizer
   14.6. A rack assembled with a bearing support
   14.7. Bottom lever
   14.8. Spherical hinge
   14.9. Nave and wheel bearing
   14.10. Top support
   14.11. Springs
   14.12. Shock-absorber
   14.13. Plugs of hinges of the bottom lever
+ 15. Drive of forward wheels
+ 16. Back suspension bracket
+ Brake system
+ Body
+ Heating, ventilation
+ Electric equipment


8128da4b Машины для перевозки замороженных продуктов.
лечебный массаж в хабаровске адреса и телефоны.



14.10. Top support

GENERAL INFORMATION

Adaptations for spring compression


Bearing of the top support of a spring rack



Arrangement of a support of a spring



To remove or disconnect

Dismantle of protective caps



Removal шплинта


Dismantle of the spherical hinge


Semi-axis dismantle


Dismantle of the bearing of the top support

PERFORMANCE ORDER
1. To lift the car and to remove a forward wheel.
2. Protective cap.
3. A bracket of a disk brake and to fix it. (The brake drive remains thus tight).
4. To establish the holder KM-468 by means of two bolts on a wheel nave. To use bolts of fastening of a wheel.
5. To remove шплинт and to unscrew a koronchaty nut of fastening of a semi-axis.
6. Выпрессовать a finger of the spherical hinge from the rotary lever of a rack by means of stripper KM-507В.
7. Выпрессовать a finger of the spherical hinge of the bottom lever from a bearing support by means of stripper KM-507В.
8. To take out manually a semi-axis from a wheel nave. If it is impossible, follows выпрессовать a semi-axis by means of a nave stripper, having mounted it in situation for a vypressovyvaniye.
9. To fix a semi-axis on weight.
Prevention

After dismantle of a semi-axis it is forbidden to load a wheel and to touch the car from a place as it can lead to axial shift of an internal ring of the bearing. If it is necessary to roll the car, it is necessary to establish temporarily in a nave a carving coupler and to tighten a koronchaty nut. (Thus the provision of rings of the bearing will be fixed).


10. To unscrew nuts of the top support of a rack and to remove a rack assembled.
11. To establish adaptations KM-465A and KM-329А for compression of a spring of a forward suspension bracket on the assembly stand or a workbench where it is possible to fix the basis for installation of adaptations. The hook with a blue label should settle down at level of a yellow label on an adaptation frame.
12. To fix a rack in the adaptation.
13. To check the provision of hooks. To compress a spring.
14. Holding from rotation a rod амортиза a rack Torah, to unscrew by means of a cap wrench a nut of the top support. It is recommended to use a bilateral cap natural available on sale by big shift of a head.
15. To dismantle from a shock-absorber rod the top support of a rack assembled with the bearing.

To establish or attach

Installation of a spring rack in the adaptation


Installation of protective caps



PERFORMANCE ORDER
1. To grease the ball-bearing with greasing for bearings. The top support of a spring rack has not folding design and is delivered only assembled with the ball-bearing.
2. To put on the top support and washers And, In a shock-absorber rod. The Tarelchaty washer And should be located under a support the unbent edge up. This metal washer carries out a role of mobile consolidation of the ball-bearing at the expense of contact of edge of a washer to an external ring of the bearing. The washer In is put on a rod from above support.
3. The ledge on a support of a spring serves as a reference point at rack installation. If to look in the direction of movement of the car, the ledge on a support of the left rack should settle down in front, and on a support of the right rack – behind.
4. To wrap a nut of fastening of a rack a cap key. To use only a new being self-stopped nut. To tighten a nut the moment of the recommended size. At an inhaling of a nut to hold from rotation a shock-absorber rod.
5. To release a spring.
6. To establish a rack on the car, to fix in a nest the top support of a rack. To tighten nuts the moment of the recommended size. To use only new being self-stopped nuts.
7. To insert a semi-axis into a shlitsevy opening of a nave of a wheel and to screw a koronchaty nut. To use only a new nut and a washer. Before installation to grease shlitsa with transmission oil.
8. To attach the spherical hinge to a bearing support of a rack, to tighten a nut the moment of the recommended size. To establish a spring clamp. To use only new a koronchaty nut and a clamp.
9. To attach the spherical hinge of steering bent for to the rotary lever of a rack. To tighten a nut the moment of the recommended size. To use only a new being self-stopped nut.
Prevention

In the bearing of a wheel should not be люфта.


10. Installation of a semi-axis to execute as follows.
10а. To insert a semi-axis into a nave and to tighten a koronchaty nut (with a washer) the moment of 100 Nanometers. Previously to attach to a nave the holder KM-468 for nave deduction from rotation.
10б. To release a koronchaty nut of fastening of a semi-axis and then to tighten it the moment of 20 Nanometers.
10в. To tighten a nut of fastening of a semi-axis on 1/4 turns.
10г. If the cut of a nut does not coincide with an opening under шплинт in a semi-axis shaft, the additional tightening of a nut is forbidden. In this case it is necessary to release a nut before opening coincidence under шплинт with a nut cut. To fix a nut the shplinty.
11. To fix a bracket of a disk brake on a bearing support of a rack. To tighten carving connections by the moment recommending wash sizes. Previously to cover new bolts with fixing structure (if bolts have no special covering). To pass a carving nest a tap of M 12 x 1,5.
12. By means of the assembly adaptation KM-404-A and KM-404-S to put on against the stop protective caps a bracket of a disk brake. To use new caps.
13. To tighten bolts of fastening of wheels in a cross order the moment of the recommended size.