Daewoo Nexia

since 1994 of release

Repair and car operation

Deu Neksiya
+ Maintenance instruction
+ Maintenance
+ Engine
+ 3. Engine (two top camshafts)
+ cooling System
+ Toplevnaya and exhaust systems
+ Electric chain
+ 7. Ignition system
+ 8. Electronic control unit and sensors
+ Transmission
- 10. Five-speed transmission and main RPO MM5 broadcast
   10.2. General description
   10.3. Diagnostics of malfunctions
   10.4. The possible reasons of the increased noise of a transmission
   10.5. Check of level of transmission oil
   10.6. Adjustment of a drive of the mechanism of switching
   10.7. Gear shifting lever
   10.8. Floor mechanism of management of a transmission
   10.9. Draft of the mechanism of management
   10.10. Intermediate lever
   10.11. Speedometer drive
   10.12. Cover of the mechanism of the switch
   10.13. Consolidations of semi-axes
   10.14. Transmissions assembled
   10.15. Dismantling of a transmission and main transfer
   10.16. Characteristic malfunctions of a transmission and possible reasons
+ 11. Automatic Transmission
+ Steering
+ Running gear
+ 14. Forward suspension bracket
+ 15. Drive of forward wheels
+ 16. Back suspension bracket
+ Brake system
+ Body
+ Heating, ventilation
+ Electric equipment

Крупа гречневая оптом и еще.

10.6. Adjustment of a drive of the mechanism of switching

GENERAL INFORMATION

Arrangement of a bolt of klemmovy connection

210. CONNECTION KLEMMOVOGO'S BOLT
239. LEVER AXIS

Arrangement of a stopper of an adjusting opening

AND. STOPPER

224. THE ROLLER WITH THE FORK

Installation of a cover of the lever of switching

AND. OVERLAY OF THE CONTROL PANEL
CENTURY. COVER
PAGE. SCREW
D. OVERLAY OF THE CENTRAL CONSOLE

Position of the lever of switching at drive adjustment

AND. ARROW
CENTURY. LABEL

Measurement of an adjusting gap

AND. DOGGIE
CENTURY. EMPHASIS
PAGE. GAP
D. ADJUSTING NUT

PERFORMANCE ORDER

1. To disconnect a negative wire of the battery.

2. To transfer the lever of switching 203 to neutral situation.

3. To weaken a bolt 210 klemmovy connections.

4. To turn out a stopper from an adjusting opening in a cover of the 235th mechanism of the switch. To turn a fork 224 so that through an adjusting opening to insert small beards in diameter of 4,76 mm into an opening of the intermediate lever of the switch 227.

5. To remove a cover 202 and to unscrew it up, to open access to the mechanism.

6. To transfer the lever of switching 203 to the provision 1 or 2nd of transfer.

6а. To achieve coincidence of an arrow to a label and to tighten a bolt 210.

6б. To tighten a bolt the moment of 14 Nanometers.

6в. After an inhaling the specified moment in addition to tighten a bolt turn on 90–180 degrees.

7. To transfer the switching lever to neutral situation and to check gap size between a doggie And and adjustment V.Posle's emphasis a gap it should be equal 3 mm.

8. To take out from openings of small beards in diameter of 4,76 mm and to establish into place a stopper.

9. To adjust by means of a nut the D gap With, as is shown in fig. Measurement of an adjusting gap. Before adjustment to unbend two pads of a clamp of a nut.

9а. The gap should be equal to 11,6 ± 0,2 mm.

9б. To fix pads регулировоч a ny nut from an otvorachivaniye.

10. To establish into place a cover 202 and an overlay of the central console.

Prevention

All transfers should join easily on the motionless car with the idling engine and the switched-off coupling.