Daewoo Nexia

since 1994 of release

Repair and car operation


Deu Neksiya
+ Maintenance instruction
+ Maintenance
+ Engine
+ 3. Engine (two top camshafts)
+ cooling System
+ Toplevnaya and exhaust systems
+ Electric chain
+ 7. Ignition system
+ 8. Electronic control unit and sensors
+ Transmission
- 10. Five-speed transmission and main RPO MM5 broadcast
   10.2. General description
   10.3. Diagnostics of malfunctions
   10.4. The possible reasons of the increased noise of a transmission
   10.5. Check of level of transmission oil
   10.6. Adjustment of a drive of the mechanism of switching
   10.7. Gear shifting lever
   10.8. Floor mechanism of management of a transmission
   10.9. Draft of the mechanism of management
   10.10. Intermediate lever
   10.11. Speedometer drive
   10.12. Cover of the mechanism of the switch
   10.13. Consolidations of semi-axes
   10.14. Transmissions assembled
   10.15. Dismantling of a transmission and main transfer
   10.16. Characteristic malfunctions of a transmission and possible reasons
+ 11. Automatic Transmission
+ Steering
+ Running gear
+ 14. Forward suspension bracket
+ 15. Drive of forward wheels
+ 16. Back suspension bracket
+ Brake system
+ Body
+ Heating, ventilation
+ Electric equipment


8128da4b



10.14. Transmissions assembled
GENERAL INFORMATION

Boltovoye transmission fastening to the engine

AND. BOLT

Arrangement of the sensor of speed of the car

A. CABLE OF THE DRIVE OF THE SPEEDOMETER
CENTURY. ELECTRIC SOCKET OF THE SENSOR OF SPEED OF THE CAR

Traverse for support of the power unit

 

Left arm

AND. BOLTS OF FASTENING OF THE ENGINE TO THE ARM
CENTURY. ARM

To remove or disconnect

Dismantle of primary shaft


PERFORMANCE ORDER
1. Negative wire of the battery.
2. Air purifier.
3. Cable of a drive and lever of the mechanism of switching off of coupling.
4. Clamp 223 and axis 237 of the kardanny hinge of a drive of management of a transmission.
5. Cable of a drive of a speedometer, socket of the sensor of speed of the car and socket of the switch of a lamp of a backing.
6. To weaken a bolt 210 klemmovy connections.
7. To turn out three top bolts of fastening of transmission to the engine.
8. To establish to a traverse.
9. To lift the car.
10. To dismantle forward wheels.
11. Antisplash guard.
12. To disconnect from a case of transmissions a condenser wire (protection against electromagnetic hindrances).
13. Выпрессовать both spherical hinges from steering levers.
14. Semi-axes.
15. Cover of a case of transmission.
16. To disconnect semi-axes from transmission.
17. To mark with paint the assembly provision of primary shaft concerning the block of gear wheels for convenience of the subsequent installation.
18. To extend primary shaft, to remove a support.
19. To hang out the power unit.
20. To remove left forward, then left back arms of the engine and to turn out the bottom bolts of fastening of a case of transmission.
21. To take aside and to remove transmission.

To establish or attach

Installation of a spring ring on the end of primary shaft

AND. SCREW

3. SPRING RING OF PRIMARY SHAFT

PERFORMANCE ORDER
1. Before installation of transmission to insert into place the right shaft as its installation later (after accession of transmission to the engine) will be impossible.
2. To screw the bottom bolts of fastening of a case of transmission to the engine and to tighten the moment of the demanded size. Moment of an inhaling of bolts of 60 Nanometers.
3. To screw bolts of the left back arm to Tighten bolts of fastening of the engine to an arm the moment of 90 Nanometers.
4. The left forward arm and to screw bolts. To tighten bolts of fastening of a forward arm to a case of transmission the moment of 60 Nanometers. To tighten bolts of fastening of an arm to a support the moment of 60 Nanometers.
5. To leave both semi-axes in a transmission case.
6. To attach spherical hinges of steering drafts and to fix them.
7. Carefully to insert primary shaft into shlitsevy openings of the block of gear wheels and a conducted disk of coupling. For shaft installation in the former provision of rather interfaced details it is necessary to be guided by a label made before dismantling.
8. To screw in a shaft the screw 67. To tighten the screw of primary shaft the moment of 15 Nanometers.
9. Spring ring 66.
10. A "mass" wire to a case cover, a stopper 53 and a wire of the condenser of protection against electromagnetic hindrances.
11. A flywheel cover to screw bolts. атянуть bolts of a cover of a flywheel moment of 7 Nanometers.
12. To screw the top bolt of fastening of transmission to the engine. To tighten the top bolt of fastening of a case of transmission to the engine the moment of 60 Nanometers.
13. Antisplash guard.
14. Both lobbies of a wheel to lower the car to Tighten bolts of fastening of wheels the moment of 90 Nanometers.
15. To attach conducting to the switch of a lamp of a backing and a cable of a drive of a speedometer.
16. To attach a cable of a drive of switching off of coupling and to adjust a drive.
17. Negative wire of the battery.

To check

PERFORMANCE ORDER
Oil level in transmission.
Refueling capacity of transmission of 1,8 l. To apply oil to mechanical transmissions of the DEUTSCH VEEDOL HD T/m brand FLUID, SAE 80.