Daewoo Nexia

since 1994 of release

Repair and car operation



Deu Neksiya
+ Maintenance instruction
+ Maintenance
+ Engine
+ 3. Engine (two top camshafts)
+ cooling System
+ Toplevnaya and exhaust systems
+ Electric chain
+ 7. Ignition system
+ 8. Electronic control unit and sensors
- Transmission
   9.2. General description
   9.3. Diagnostics of malfunctions
   9.4. Cable of a drive of coupling
   9.5. Coupling pedal
   9.6. Conducted and press disks, a coupling drive
   9.7. Air removal from a hydraulic drive of coupling
   9.8. Main cylinder
   9.9. Working cylinder of coupling
   9.10. Main malfunctions of coupling, their reason and ways of elimination
+ 10. Five-speed transmission and main RPO MM5 broadcast
+ 11. Automatic Transmission
+ Steering
+ Running gear
+ 14. Forward suspension bracket
+ 15. Drive of forward wheels
+ 16. Back suspension bracket
+ Brake system
+ Body
+ Heating, ventilation
+ Electric equipment


8128da4b



9.7. Air removal from a hydraulic drive of coupling

GENERAL INFORMATION

Coupling with a hydraulic drive

 

1. THE ROLLER WITH THE LEVER OF SWITCHING OFF OF COUPLING
2. BOLT
3. SPRING WASHER
4. BOLT
5. FLAT WASHER
6. NUT
7. BOLT
8. ARM OF THE WORKING CYLINDER
9. WORKING CYLINDER
10. COPPER WASHER
11. BOLT
12. THE HOSE WITH TIPS
13. ARM
14. CLIP
15. PIPELINE
16. MAIN CYLINDER
17. COPPER WASHER
18. HOSE UNION
19. SPRING COLLAR
20. TANK
21. HOSE
22. BOLT
23. TANK ARM
24. NUT
25. FINGER
26. CLIP
27. RETURNABLE SPRING
28. PLUG
29. COURSE LIMITER PEDALS (TOP)
30. COUPLING PEDAL
31. OVERLAY OF THE PEDAL
32. AXIS
33. WASHER
34. NUT
35. SPRING ШПЛИНТ
36. PEDAL ARM
37. BOLT
38. LOCK-NUT
39. FLANGE
40. PALLET
41. BOLT
42. CONSOLIDATION OF PRIMARY SHAFT
43. SEALING RING
44. BEARING VYZHIMNOGO'S DIRECTING PLUG
45. VYZHIMNA BEARING
46. FORK
47. PLUG
48. WASHER
49. BOLT
50. THE CONDUCTED DISK
51. CASING OF COUPLING WITH THE PRESS DISK ê SPRING
52. WASHER
53. BOLT
54. PLUG BOLT
55. NUT
56. PLUG
57. ROD
58. LOCK-NUT
59. THE VALVE FOR AIR REMOVAL

Air removal from a coupling hydraulic actuator

9. WORKING CYLINDER
59. THE VALVE FOR AIR REMOVAL

PERFORMANCE ORDER
1. After completion of repair and assembly of a hydraulic drive it is necessary to remove from it air.
2. In the course of hydraulic actuator pumping for removal of air it is necessary to support in a tank level of working liquid not below MIN label.
3. To put on the valve of production of air the end of a vinyl hose. Other end of a hose to lower in transparent capacity, наполови well filled with brake liquid.
4. Several times slowly to press a coupling pedal.
5. At the pressed pedal of coupling partially to unscrew the valve for production of air. After the termination of an effluence of liquid from the hose which has been put on the valve to wrap the valve.
6. To repeat operations 4 and 5 several times while vials of air will not cease to leave together with working liquid.
7. After completion of pumping гидроприво yes to add in a tank brake liquid and to finish its level to a label the MOVE.