Daewoo Nexia

since 1994 of release

Repair and car operation


Deu Neksiya
+ Maintenance instruction
+ Maintenance
+ Engine
+ 3. Engine (two top camshafts)
+ cooling System
+ Toplevnaya and exhaust systems
+ Electric chain
+ 7. Ignition system
+ 8. Electronic control unit and sensors
- Transmission
   9.2. General description
   9.3. Diagnostics of malfunctions
   9.4. Cable of a drive of coupling
   9.5. Coupling pedal
   9.6. Conducted and press disks, a coupling drive
   9.7. Air removal from a hydraulic drive of coupling
   9.8. Main cylinder
   9.9. Working cylinder of coupling
   9.10. Main malfunctions of coupling, their reason and ways of elimination
+ 10. Five-speed transmission and main RPO MM5 broadcast
+ 11. Automatic Transmission
+ Steering
+ Running gear
+ 14. Forward suspension bracket
+ 15. Drive of forward wheels
+ 16. Back suspension bracket
+ Brake system
+ Body
+ Heating, ventilation
+ Electric equipment


8128da4b



9.5. Coupling pedal
GENERAL INFORMATION

Fastening of a tip of a cable to the lever of switching off of coupling

2. CLIP
3. CABLE TIP
4. NUT

Fastening of a pedal of coupling

7. ШПЛИНТ
8. NUT
9. WASHER
11. AXIS
12. RETURNABLE SPRING

Cable fastening to a coupling pedal

3. CABLE HAKOHEÙÌÊK
12. RETURNABLE SPRING
14. PEDAL

To remove or disconnect

PERFORMANCE ORDER
1. Negative wire of the storage battery.
2. To measure free length of a carving tip of a cable. To write down result of measurement.
3. A tip of a cable 3 from the lever of the roller of 1 switching off of coupling.
3а. To remove a clip 2.
3б. To unscrew a nut 4.
4. Switch of blocking of start of the engine.
5. Coupling pedal.
5а. A returnable spring 12 from a kerchief 10.
5б. Шплинт 7.
5в. Nut 8.
5г. Washer 9.
5д. Axis 11.
5е. Pedal 14.
6. A returnable spring 12 and a cable tip from a pedal 14.

To establish or attach

PERFORMANCE ORDER
1. To attach a tip of a cable and a returnable spring 12 to a pedal 14.
2. To grease an axis 11 with konsistentny N 1052349 greasing or equivalent.
3. To establish a pedal 14 between kerchiefs 10 of a steering column.
4. To insert into openings of kerchiefs 10 and a pedal the 14th axis 11.
4а. To put on a washer 9.
4б. To screw a nut 8.
4в. To insert шплинт 7.
4г. To insert a returnable spring 12 into a kerchief 10.
5. Switch of blocking of start of the engine.
6. A tip 3 cables to the lever of the roller of 1 switch of coupling.
7. To screw a nut 4 in situation which it occupied before cable dismantle.
8. To adjust a drive cable.
9. Clip 2.
10. Negative wire of the battery.

To adjust (with a hummock drive)

PERFORMANCE ORDER
1. To release a lock-nut 38 and rotation of a bolt 37 to adjust a pedal course.
2. To adjust a free wheeling of a pedal, having released a lock-nut 58 and rotating a rod 57. The nominal size of a free wheeling of a pedal is equal 8–15 mm.
3. After adjustment to tighten a lock-nut 58.
4. To check size of a free wheeling of a pedal as follows. To press a pedal a hand with small effort and to measure pedal moving from initial situation before situation when resistance to pedal moving starts to increase.

To adjust (with a hydraulic drive)

PERFORMANCE ORDER
1. To turn on the parking brake.
2. To start the Engine and to deduce it on idling.
3. Having made small effort on the transmission lever for inclusion of transfer of a backing, slowly to press a coupling pedal. To measure distance from the provision of the pedal corresponding to the termination of a gnash of teeths of included gear wheels, to the extreme provision of completely pressed pedal. This distance should exceed 25 mm.
4. If the result of measurement does not correspond to the specified requirement, it is necessary to check the following:
– height of an arrangement of a pedal of coupling;
– size of a free wheeling of a pedal of coupling;
– availability of air in a coupling hydraulic actuator;
– condition of a disk of coupling.