Daewoo Nexia

since 1994 of release

Repair and car operation



Deu Neksiya
+ Maintenance instruction
+ Maintenance
+ Engine
+ 3. Engine (two top camshafts)
+ cooling System
+ Toplevnaya and exhaust systems
+ Electric chain
+ 7. Ignition system
- 8. Electronic control unit and sensors
   - 8.2. Sensors
      8.2.2. The air temperature sensor in an inlet collector (pipeline) (DTV)
      8.2.3. The sensor of concentration of oxygen in the fulfilled gases (DKK)
      8.2.4. Sensor of provision of a butterfly valve (DDZ)
      8.2.5. The sensor of absolute pressure in the inlet pipeline (DAD)
      + 8.2.6. Sensor of speed of the car (DSA)
      8.2.7. Sensor of inclusion of central air of air
      8.2.8. Parking/neutral switch (an automatic transmission)
+ Transmission
+ 10. Five-speed transmission and main RPO MM5 broadcast
+ 11. Automatic Transmission
+ Steering
+ Running gear
+ 14. Forward suspension bracket
+ 15. Drive of forward wheels
+ 16. Back suspension bracket
+ Brake system
+ Body
+ Heating, ventilation
+ Electric equipment


8128da4b



8.2.8. Parking / neutral switch (an automatic transmission)

GENERAL INFORMATION

Parking / neutral switch

 


Parking / neutral switch and switch of a lamp of a backing


1. BOLT, MOMEIT of the INHALING of 30 Nanometers
2. SWITCH
3. ROLLER OF SWITCHING OF RANGES
4. THE ADJUSTING OPENING IN THE SWITCH CASE
5. MEASURING CORE in DIAMETER of 2,34 mm

The electric socket of the switch with T-shaped

1. PARKING / NEUTRAL SWITCH AND SWITCH OF THE LAMP OF THE BACKING
2. SWITCH SOCKET T-SHAPED CLAMP

The Parking / neutral switch is intended for control of position of the selector of an automatic transmission. The signal of the switch is used by EBU at management of the valve of idling of the engine.
Prevention

Car operation is forbidden at the disconnected socket of the Parking / neutral switch as it will lead to violation of operation of the engine idling. Delivery of a code of malfunction 24 (failure of the sensor of speed of the car) is possible also.


To remove or disconnect

PERFORMANCE ORDER
1. Mechanical drive of the selector of ranges.
2. Electric socket.
3. Fixing bolts.
4. Switch.

SWITCH REPLACEMENT – INSTALLATION OF THE SWITCH WHICH WAS IN THE USE

To establish or attach

PERFORMANCE ORDER
1. To turn the roller of switching of ranges in neutral situation.
2. The switch, сориентировав its opening on лыскам the roller.
3. To screw, without tightening, bolts.
4. To insert into an adjusting opening of the case of the switch a measuring core and to turn the switch so that the core was drowned on 9 mm.
5. To tighten bolts.

To remove or disconnect

PERFORMANCE ORDER
To take out a core.
Prevention

After adjustment of the switch it is necessary to check blocking of start-up of the engine in all positions of the selector of ranges, except a neutral and "Parking". If the Engine is started and in other positions of the selector, to repeat adjustment.



SWITCH REPLACEMENT – INSTALLATION OF THE NEW SWITCH

To establish or attach

PERFORMANCE ORDER
1. To turn the roller of switching of ranges in neutral situation.
2. The switch, сориентировав its opening on лыскам the roller.
3. To screw and tighten bolts. If openings for bolts do not coincide with carving openings in a transmission case, it is necessary to check position of the roller and to establish it in neutral situation, without turning the switch. The switch is in neutral situation. If the switch was turned, it is necessary to adjust it similar to the switch which was in the use.
Prevention

After adjustment of the switch it is necessary to check blocking of start-up of the engine in all positions of the selector of ranges, except a neutral and "Parking". If the Engine is started and in other positions of the selector, to make the adjustment applied at installation of the switch which was in the use.



To adjust

PERFORMANCE ORDER
1. To transfer the selector of ranges to neutral situation.
2. To weaken fixing bolts of the switch.
3. To turn the switch on the roller before coincidence of an adjusting opening of the switch to an opening in a pad of the holder. To insert a measuring core in diameter of 2,34 mm on depth of 15 mm.
4. To tighten bolts the demanded moment.
5. To take out a measuring core.