Deu Neksiya
+ Maintenance instruction
+ Maintenance
+ Engine
+ 3. Engine (two top camshafts)
+ cooling System
+ Toplevnaya and exhaust systems
+ Electric chain
- 7. Ignition system
7.2. Diagnostics of malfunctions of a spark plug
7.3. Ignition distributor
7.4. Ignition coil
7.5. Repair of the distributor of ignition
7.6. System of regulation of an advancing of ignition
7.7. Installation of the moment of ignition
+ 8. Electronic control unit and sensors
+ Transmission
+ 10. Five-speed transmission and main RPO MM5 broadcast
+ 11. Automatic Transmission
+ Steering
+ Running gear
+ 14. Forward suspension bracket
+ 15. Drive of forward wheels
+ 16. Back suspension bracket
+ Brake system
+ Body
+ Heating, ventilation
+ Electric equipment
|
Check of the coil of ignition
|
|
1. OHMMETER
2. PLUGS C AND ТАСН
3. OHMMETER
4. PLUG B
5. OHMMETER |
| PERFORMANCE ORDER |
| 1. To check windings of the coil of ignition on existence of gaps and short circuit on "weight". |
| Step 1. To switch an ohmmeter to the most rough range. The measured resistance should be very great ("infinitely"). Otherwise to replace the coil. |
| Step 2. To switch an ohmmeter to the most sensitive range. The measured resistance should be very little (closely to zero). Otherwise to replace the coil. |
| Z.Pereklyuchit's step an ohmmeter on the most rough range. The measured resistance should not be very big, as on a step 1. Otherwise to replace the coil. |
|
Check of the coil of the magnetoelectric sensor
|
|
1. ELECTRONIC MODULE
2. COIL OF THE MAGNETOELECTRIC SENSOR ASSEMBLED
3. WIRES OF THE COIL OF THE SENSOR, DISCONNECTED FROM THE ELECTRONIC MODULE
4. OHMMETER
5. OHMMETER |
| PERFORMANCE ORDER |
| 2. To remove a rotor and to disconnect wires of the coil of the sensor from the electronic module. |
| 3. Consistently to attach an ohmmeter in the ways 1 and 2, see fig. Check of the coil of the magnetoelectric sensor. |
| 4. To check the coil on gap existence. |
| Step 1. The measured resistance should be very great ("infinitely"). Otherwise to replace the coil. |
| Step 2. The measured resistance should be in limits of 500-1500 Ohm. If the size of resistance oversteps the bounds of this range, it is necessary to replace the coil. |
|
Dismantle of a pin of the leading coupling
| PERFORMANCE ORDER |
| 5. To remove a spring. To put labels on the leading coupling and the roller for simplification of the subsequent assembly. Опереть the coupling on At-shaped.......... To beat out a pin and to remove the coupling. To remove with a file all agnails and to take out the roller. |
|
Dismantle of the coil of the magnetoelectric sensor
| PERFORMANCE ORDER |
| 6. To dismantle the coil, it is necessary to remove a thin spring ring previously. |
| 7. To remove the coil, having lifted it up. |
|
Dismantle of the electronic module
| PERFORMANCE ORDER |
| 8. To disconnect the electric socket of the module, to turn out two screws and to remove the module. To check the module by means of the test equipment. |
| 9. To wipe absolutely the basis распреде a litel and the module and to grease a module installation site with siliceous greasing for heat-conducting path improvement from the module. |
| 10. To establish and fix the module. To connect the socket. |
| 11. To establish the coil of the sensor and a thin spring ring. |
| 12. To assemble the roller, the coupling and to establish a pin. |
| 13. To turn the roller to check freedom of its rotation. |
| 14. At a zadevaniye of the roller to weaken fastening of the coil of the sensor, to eliminate a zadevaniye and to fix again. |
| 15. To establish a rotor and a cover. |
|
|
|
