Deu Neksiya
+ Maintenance instruction
+ Maintenance
+ Engine
+ 3. Engine (two top camshafts)
+ cooling System
+ Toplevnaya and exhaust systems
+ Electric chain
+ 7. Ignition system
+ 8. Electronic control unit and sensors
+ Transmission
+ 10. Five-speed transmission and main RPO MM5 broadcast
- 11. Automatic Transmission
11.2. The terms, the accepted reductions and abbreviations
11.3. General description of transmission
11.4. Main knots of a transmission
11.5. Methods of localization of leakages of working liquid
11.6. Check of level of working liquid in transmission the 4Т40th
11.7. Diagnostics of malfunctions of knots of transmission
+ Steering
+ Running gear
+ 14. Forward suspension bracket
+ 15. Drive of forward wheels
+ 16. Back suspension bracket
+ Brake system
+ Body
+ Heating, ventilation
+ Electric equipment
|
Transmission noise
• Noise of chain transfer – the howling or roaring noise, which level increases or decreases at change of frequency of rotation of country houses of the engine. Noise is absent at car dispersal with a small corner of opening of DZ and in engine operating time on a place at inclusion in a transmission of ranges D (Movement) or R (Backing).
• Noise of the main transfer – a rumble, which level depends on speed of movement of the car. The rumble is especially appreciable at car dispersal with small extent of opening of DZ and during movement nakaty with the released pedal of an accelerator.
• Noise of planetary transfer – howling noise which is most strongly shown on the 1st transfer and transfer of a backing and depends on speed of the car. Noise of planetary transfer can decrease or vanish when switching transmission on an adjacent highest step.
• Pump noise – the howling sound of a high-pitch tone increasing with growth of turns of the engine. Noise of the pump can be audible on all transfers.
• Hydrotransformer noise – howling noise which is usually audible only on the motionless car at inclusion in a transmission of ranges D (Movement) or R (Backing). Noise of GT increases with growth of turns of the engine.
High or low pressure of working liquid in the trunk main
It is checked by means of a plotnomer (all switchings occur roughly or too slowly).
Possible codes of malfunctions:
– 502 Sensor of speed of the car – a low voltage of a signal
– 503 Sensor of speed of the car – an unstable or chaotic signal
– 712 Sensor of temperature of working liquid of transmission – a low voltage of a signal
– 713 Sensor of temperature working transmission liquids – a high voltage of a signal
– 716 Sensor of speed of rotation of an entrance shaft – low frequency of a signal
– 717 Sensor of speed of rotation of an entrance shaft – a signal is absent
– 748 EMK of a regulator of pressure – refusal of an electric chain
– 751 EMK of the switch A – the executive distributor
– 753 EMK of the switch A – the executive distributor
– 756 EMK of the switch B – the executive distributor
– 758 EMK of the switch B – refusal of an electric chain
– 1560 Deviation of tension of an electric network from norm
– 1810 Malfunction of the switch of control of ranges (block of the relay of pressure)
– 1871 Wrong transfer number
– 1887 Relays of pressure of a friction clutch of blocking of GT
| TO CHECK | REASON |
| Level of working liquid | Too high or low level to finish level of working liquid to norm |
|
Valve of a regulator of pressure, spring and busterny valve
| Valve jamming |
| EMK of a regulator of pressure | Leakage of liquid, damage of sealing rings |
| Weakening of fastening of the socket, damage of pins |
| Pollution |
| The regulator valve on loading (torque) of the engine | Valve jamming |
| Transmission electroconducting | Weakening of fastening of the socket, short circuit |
| Block of the relay of pressure | Weakening of fastening of the socket |
| Damage or lack of sealing rings |
| Filter of working liquid | Contamination or damage of a filtering element, weakening of fastening of the filter |
| – Filter consolidation | Leakage of working liquid |
| Heat exchanger pipelines | Zabivaniye of section through passage or deformation of pipelines |
|
Hydropump | Breakage, jamming, porosity of the case or leak |
| Shaft of a drive of the hydropump | Breakage |
| Safety valve | Spring breakage, lack of a ball |
| Transmission case, control panel transmission, distributive panel | Porosity of a case, leak from the highway |
| Violation of planeness of interfaced surfaces |
Violation of accuracy or sequence of the moments of switching
Possible code of malfunction:
– 502 Sensor of speed of the car – a low voltage of a signal
– 503 Sensor of speed of the car – not abutment a chivy or chaotic signal
– 716 Sensor of speed of rotation of an entrance shaft – low frequency of a signal
– 717 Sensor of speed of rotation of an entrance shaft – a signal is absent
– 751 EMK of the switch A – the executive distributor
– 753 EMK of the switch A – the executive distributor
– 756 EMK of the switch B – the executive distributor
– 758 EMK of the switch B – refusal of an electric chain
– 1560 Deviation of tension of an electric network from norms
|
TO CHECK
|
REASON
|
|
EMK of switches
|
Pollution
|
|
Unstable gap or short circuit of a chain
|
|
Sensor of provision of a butterfly valve
|
Breakage or detachment
|
|
Unstable gap or short circuit of a chain
|
|
Sensors of speed of the car and speed of rotation of an entrance shaft
|
Breakage, detachment or weakening of fastening
|
|
Unstable gap or short circuit of a chain
|
Rough gear shifting
|
TO CHECK
|
REASON
|
|
Pressure in the trunk main
|
High pressure of working liquid
|
|
Ball return valves
|
Absence, is not present an inclusion delay
|
|
Dampers of inclusion of transfers
|
Piston or spring jamming, damper does not operate
|
|
Jamming of the valve of a damper
|
|
Stopper of the case and ball valve assembled
|
Blockage
|
Backing transfer, slipping of frictional knots on backing transfer does not join
| TO CHECK | REASON |
|
Friction clutch of transfers of a forward course
|
Absence of inclusion, friction clutch slipping
|
|
– The piston assembled with consolidation
|
Jamming, existence of cracks, leakages of working liquid
|
|
– Internal consolidation
|
Opening blockage
|
|
– Friction clutch disks
|
Wear of slips, breakage of shlitsevy teeths
|
|
– Spring ring
|
Shift from normal situation
|
|
– Case
|
Existence of cracks, blockage of highways
|
|
– Stopper of the case and ball valve assembled
|
Absence or shift from normal situation
|
|
– Spring
|
Jamming
|
|
Highways of a supply of working liquid in a piston cavity of a friction clutch
|
Leakage of liquid or high resistance to a liquid stream
|
|
– A support of a conducted asterisk
|
Porosity existence, leak through sealing rings, damage or a blockage of highways
|
|
– Distributive panel and laying, control panel and laying
|
Porosity existence, mixture from normal situation, a liquid peretechka between channels, high resistance to a liquid stream
|
|
Tape brake of transfer of a backing and 1 transfers, сервоцилиндр
|
There is no inclusion, slipping
|
|
– Piston
|
Breakage, jamming
|
|
– Piston consolidations
|
Leakage of working liquid
|
|
– Rod and spring
|
Jamming
|
|
– Cover сервоцилиндра
|
Breakage, weakening of fastening leakage of working liquid
|
|
– Brake tape
|
Breakage, wear, shift from normal situation
|
|
– Pin
|
Breakage
|
|
– Hydraulic highways
|
Breakage, deformation, blockage, lack of sealing rings, leakages of working liquid
|
|
– Transmission case
|
Porosity, leakages of working liquid or high resistance to a liquid stream
|
|
Mechanical drive of the switch of ranges
|
Detachment, shift
|
|
Zolotnik of the switch of ranges
|
Detachment, shift
|
|
Ball return valve 1 (LO/PRN)
|
Absence
|
|
Level of working liquid
|
Low level
|
|
Pressure of working liquid
|
|
The first transfer, slipping of frictional knots on the first transfer does not join
Possible code of malfunction:
– 502 Sensor of speed of the car – a low voltage of a signal
– 503 Sensor of speed of the car – an unstable or chaotic signal
– 716 Sensor of speed of rotation of an entrance shaft – low frequency of a signal
– 717 Sensor of speed of rotation of an entrance shaft – a signal is absent
– 751 EMK of the switch A – the executive distributor
– 753 EMK of the switch A – the executive distributor
– 756 EMK of the switch B – the executive distributor
– 758 EMK of the switch B – refusal of an electric chain
| TO CHECK | REASON |
|
Friction clutch of transfers of a forward course
|
Absence of inclusion, friction clutch slipping
|
|
– The piston assembled with consolidation
|
Jamming, existence of cracks, leakages of working liquid
|
|
– Internal consolidation
|
Opening blockage
|
|
– Friction clutch disks
|
Wear of slips, breakage of shlitsevy teeths
|
|
– Spring ring
|
Shift from normal situation
|
|
– Case
|
Existence of cracks, blockage of highways
|
|
– Stopper of the case and ball valve assembled
|
Absence or shift from normal situation
|
|
– Springs
|
Jamming
|
|
MCX braking by the engine
|
Breakage, provorachivaniye
|
|
MCX 1st transfer
|
Breakage, provorachivaniye
|
|
Highways of a supply of liquid to a piston cavity of a friction clutch of transfers of a forward course
|
Leakage of liquid or high resistance to a liquid stream
|
|
– Tubes of a supply of liquid
|
Deformation, breakage, leak through a sealant ny rings, a blockage
|
|
– Support of a friction clutch of transfers of a forward course
|
Porosity existence, leak through sealing rings, damage or a blockage of highways
|
|
– Distributive panel and laying
|
Porosity existence, mixture from normal situation, a liquid peretechka between channels, high resistance to a liquid stream
|
|
– Block of the relay of pressure
|
Leakage of consolidations of the block of the relay of pressure
|
|
Switch A EMK
|
Impossibility to include EMK, leakage of liquid
|
|
Valve of the switch of transfers 1-2
|
Zolotnik jamming in the provision of the 2nd transfer
|
|
Switch B EMK
|
Impossibility to switch off EMK, blockage of a drain opening
|
|
Zolotnik and mechanical drive of the switch of ranges
|
Zolotnik mixture from normal situation
|
|
Hydrotransformer
|
Provorachivaniye MCX of the GT reactor
|
|
Pressure of liquid in the trunk main
|
Low pressure
|
The second transfer, slipping of frictional knots on the second transfer does not join
Possible code of malfunction:
– 751 EMK of the switch A – the executive distributor
– 753 EMK of the switch A – the executive distributor
|
TO CHECK
|
REASON
|
|
Friction clutch of the 2nd transfer
|
Absence of inclusion, friction clutch slipping
|
|
– The piston assembled with consolidation
|
Jamming, existence of cracks, leakage of working liquid
|
|
– Friction clutch disks
|
Wear of slips, breakage of shlitsevy teeths
|
|
– Spring ring
|
Shift from normal situation
|
|
– Springs
|
Jamming
|
|
– A support of a conducted asterisk
|
Damage existence of cracks, blockage of openings
|
|
Highways of a supply of liquid to a piston cavity of a friction clutch of the 2nd transfer
|
Leakage of liquid or high resistance to a liquid stream
|
|
– Control panel, laying and distributive plate, distributive panel and laying: a support of a conducted asterisk
|
Porosity existence, mixture from normal situation, weakening of fastening, high resistance to a liquid stream, a liquid overflowing between channels
|
|
MCX 2nd transfer
|
Breakage, provorachivaniye
|
|
Switch A EMK
|
Jamming in the included situation, a blockage
|
|
Distributor and zolotnik of gear shifting 1-2
|
Jamming in the provision of the 1st transfer
|
|
Pressure of liquid in the trunk main
|
Low pressure
|
|
Damper of gear shifting 1-2
|
Leakage of liquid through piston consolidations
|
|
Porosity of the distributive panel or case
|
|
Distributor and damper zolotnik
|
Jamming
|
The third transfer, slipping of frictional knots on the third transfer does not join
Possible codes of malfunctions:
– 756 EMK of the switch B – the executive distributor
– 758 EMK of the switch B – refusal of an electric chain
| TO CHECK | REASON |
|
Friction clutch of the 3rd (direct) transfer
|
Absence of inclusion, friction clutch slipping
|
|
– The piston assembled with consolidation
|
Jamming, existence of cracks, leakage of working liquid
|
|
– Disks
|
Wear of slips, breakage of shlitsevy teeths
|
|
– Spring ring
|
Shift from normal situation
|
|
– Springs
|
Jamming
|
|
– Case of a friction clutch and entrance shaft
|
Damage existence of cracks, blockage of openings
|
|
– Stopper of the case and ball valve assembled
|
Absence or weakening of fastening
|
|
Highways of a supply of liquid in a piston cavity of a friction clutch of the 3rd transfer
|
Porosity existence shift from normal situation, weakening of a kropleniye, a liquid peretechka between channels, high resistance to a liquid stream
|
|
– The control panel, laying and a distributive plate, distribute the telny panel and laying, a support of a conducted asterisk
|
|
– Consolidations of a support of a conducted asterisk
|
Leakage of liquid
|
|
– Entrance shaft
|
Leakage of consolidations
|
|
Plug damage, mixture from normal situation
|
|
Switch B ZMK
|
Jamming in the switched-off situation, leakages of liquid
|
|
Distributor and zolotnik of gear shifting 2-3
|
Jamming
|
|
Damper of gear shifting 2-3
|
Leakage of liquid through piston consolidation
|
|
Porosity of the distributive panel or case
|
|
Distributor and zolotnik of a damper 2-3
|
Jamming
|
|
Ball return valve 5 (inclusions of a friction clutch 3 and transfers)
|
Absence
|
|
Pressure of liquid in the trunk main
|
Low pressure
|
The fourth transfer, slipping of fractional knots on the fourth transfer does not include
Possible codes of malfunctions:
– 751 EMK of the switch A – the executive distributor
– 753 EMK of the switch A – the executive distributor
|
TO CHECK
|
REASON
|
|
Tape brake of the 4th transfer and сервоцилиндр
|
Absence of inclusion, slipping
|
|
– Piston сервоцилиндра
|
Breakage, jamming
|
|
– Piston consolidations
|
Leakage of liquid
|
|
– Piston and spring rod
|
Jamming
|
|
– Servo-driver cover
|
Breakage, weakening of fastening, leakage of liquid
|
|
– Tape
|
Breakage, wear, shift from normal situation
|
|
– Case
|
Crack about a tape arm
|
|
Highways of a supply of liquid to сервоцилиндру
|
Porosity, shift from normal situation, weakening of fastening, big resistance to a liquid stream, leakage of liquid between channels
|
|
– Valve case, laying and distributive plate, distributive panel, case
|
|
Switch A EMK
|
Jamming in the switched-off situation
|
|
Distributor and zolotnik rekey niya of transfers 3-4
|
Jamming
|
|
Zolotnik of the switch of ranges
|
Shift from normal situation (in the provision of a range 3)
|
|
Damper of gear shifting 3-4
|
Leakage of liquid through piston consolidation
|
|
Porosity of the distributive panel or case
|
|
Distributor of a damper 3-4
|
Jamming
|
|
Pressure in the trunk main
|
Low pressure
|
The car does not get under way from a place
|
TO CHECK
|
REASON
|
|
Hydrotransformer
|
Breakage of assembly ledges, destruction of welded seams
|
|
Cut of fixing bolts
|
|
Wear of shliyets of a shaft of the turbine
|
|
Breakage of shovels of wheels
|
|
Case cracks on welded seams
|
|
Shaft of a turbine wheel
|
Removal or cut of shliyets
|
|
Hydropump
|
Jamming or breakage of plates of a rotor
|
|
Shaft of a drive of the hydropump
|
Breakage cut or smyaty shliyets
|
|
Filter and filter consolidation
|
Zabivaniye, absence
|
|
Level of working liquid
|
Low level of working liquid
|
|
Mechanical drive of the switch of ranges
|
Detachment
|
|
Chain transfer, asterisks and chain
|
Breakage
|
|
Planetary transfer
|
Breakage, lack of greasing
|
|
Main transfer
|
Gear wheel breakage, lack of greasing
|
|
Distributive panel and laying
|
Damage, leakage of liquid, shift from normal situation
|
|
Control panel, laying and distributive plate
|
Damage, leakage of liquid, shift from normal situation
|
|
MCX and friction gear of a forward course. MCX 1st transfer
|
Damage, provorachivaniye
|
Deterioration of dynamics of the car
Possible codes of malfunctions:
– 751 EMK of the switch A – the executive distributor
– 753 EMK of the switch A – the executive distributor
– 756 EMK of the switch B – the executive distributor
– 758 EMK of the switch B – refusal of an electric chain
|
TO CHECK
|
REASON
|
|
Level of working liquid
|
Low level of liquid
|
|
Gear shifting EMK
|
Both EMK are switched off, the car gets under way on the 2nd transfer
|
|
EMK of the switch B is not switched off
|
|
System of blocking of GT
|
Jamming in the included situation or incomplete switching off of a friction clutch of blocking of GT
|
|
Hydrotransformer
|
Damage or contamination
|
Engine stop
|
TO CHECK
|
REASON
|
|
System of blocking of GT
|
Jamming in the included situation or incomplete switching off of a friction clutch of blocking of GT
|
|
– EMK of a friction clutch of blocking of GT
|
Jamming in the included situation, закупорива scientific research institute of a drain opening
|
|
– Distributor of management of a blocking friction clutch
|
Jamming in the provision of inclusion of a friction clutch
|
The 1st and 2nd transfers join only
Possible codes of malfunctions:
– 756 EMK of the switch B – the executive distributor
– 758 EMK of the switch B – refusal of an electric chain
– 751 EMK of the switch A – the executive distributor
– 753 EMK of the switch A – the executive distributor
|
TO CHECK
|
REASON
|
|
Switch B EMK
|
Jamming in the switched-off situation, leakage of liquid via the valve, refusal of an electric chain
|
|
Distributor and zolotnik rekey niya of transfers 2-3
|
Jamming in the provision of inclusion of the 2nd transfer
|
|
Switch A EMK
|
Jamming in included situation, закупорива valve scientific research institute, refusal electric chains
|
The 2nd and 3rd transfers join only
Possible codes of malfunctions:
– 751 EMK of the switch A – the executive distributor
– 753 EMK of the switch A – the executive distributor
|
TO CHECK
|
REASON
|
|
Switch A EMK
|
Jamming in included situation, refusal electric chains, leakage of liquid via the valve
|
The 3rd and 4th transfers join only
Possible codes of malfunctions:
– 756 EMK of the switch B – the executive distributor
– 758 EMK of the switch B – refusal of an electric chain
|
TO CHECK
|
REASON
|
|
Switch B EMK
|
Jamming in the included situation, закупорива valve scientific research institute, refusal of an electric chain
|
|
Distributor and zolotnik rekey niya of transfers 2-3
|
Jamming in the provision of inclusion of the 3rd transfer
|
The range P (parking) does not join
|
TO CHECK
|
REASON
|
|
Mechanism of inclusion of blocking of a target shaft
|
Bend or rod damage
|
|
Breakage or spring jamming
|
|
Rod detachment from the stopper lever
|
|
Roller and spring
|
Weakening of an inhaling of a bolt
|
|
Bend or damage
|
|
Stopper lever
|
Damage, weakening of fastening (lack of a pin of a rod)
|
|
Zolotnik of the switch of ranges
|
Shift from normal situation, deformation of a drive of the lever of a stopper
|
|
Cogwheel, blocking mechanism
|
Damage of teeths or shliyets
|
|
Stopper
|
Damage, breakage of teeths
|
|
Stopper spring
|
Breakage, absence
|
|
Drive of the mechanism of blocking
|
Adjustment violation
|
Noise of a gnash of teeths
|
TO CHECK
|
REASON
|
|
Stopper
|
Damage, easing or detachment of a returnable spring
|
Inefficient braking by the engine on all ranges
|
TO CHECK
|
REASON
|
|
Friction clutch of braking by the engine
|
Absence of inclusion, slipping
|
|
– Piston and consolidation
|
Jamming, cracks of leakage of liquid
|
|
– Disks
|
Wear of frictional slips, breakages шлицов
|
|
– Springs
|
Jamming
|
|
– Case and entrance shaft
|
Damage, cracks, blockage of channels
|
|
– Stopper of the case and ball valve assembled
|
Absence or weakening of fastening
|
|
Highways of a supply of working liquid to a piston cavity of a friction clutch
|
Porosity, mixture from normal situation, weakening of fastening, resistance to a liquid stream, leakage of liquid between channels
|
|
– Laying of the control panel and a distributive plate, distribute the telny panel and laying, a support of a conducted asterisk
|
Leakage of liquid
|
|
– Consolidations, a support of a conducted asterisk
|
Consolidation leakage
|
|
– Entrance shaft
|
Damage or shift from normal position of the plug
|
|
Level of working liquid and pressure in the trunk main
|
Low pressure or level
|
|
Distributor and zolotnik of gear shifting 3-4
|
Zolotnik jamming in the provision of the 4th transfer
|
|
Zolotnik of the switch of ranges and its drive
|
Shift from normal situation
|
Inefficient braking by the engine in a range 2
Possible codes of malfunctions:
– 1810 Malfunction of the switch of control of ranges (block of the relay of pressure)
|
TO CHECK
|
REASON
|
|
Friction clutch of braking by the engine
|
Absence of inclusion, slipping
|
|
Tape brake of the 4th transfer
|
Absence of inclusion slipping
|
|
Block of the relay of pressure
|
Leakage of liquid, the relay it is not efficient
|
Inefficient braking by the engine in a range 1
Possible codes of malfunctions:
– 1810 Malfunction of the switch of control of ranges (block of the relay of pressure)
|
TO CHECK
|
REASON
|
|
Friction clutch of braking by the engine
|
Absence of inclusion, slipping
|
|
Servotsilindr of a tape brake of the 1st transfer and backing transfer
|
Absence of inclusion, slipping, absence of inclusion of a tape brake of the 1st transfer and backing transfer
|
|
Block of the relay of pressure
|
Leakage of liquid, the relay it is not efficient
|
|
Step-by-step return valve 1
|
Absence
|
Troganiye of the car at the included range of N
|
TO CHECK
|
REASON
|
|
Friction clutch of transfers of a forward course
|
It is not switched off
|
|
Friction clutch of transfer of a backing and сервоцилиндр tape brake 1 transfers and backing transfers
|
Both frictional elements are not switched off
|
|
Zolotnik of the switch of ranges and its drive
|
Shift from normal situation
|
Ranges do not join
|
TO CHECK
|
REASON
|
|
Zolotnik of the switch of ranges and drive of the lever of a stopper
|
Breakage, absence
|
|
Detachment from a zolotnik of the switch of ranges
|
|
Clamp of draft of a zolotnik of the switch of ranges
|
Detachment
|
|
Zolotnik of the switch of ranges
|
Jamming
|
|
Mechanical drive of the switch of ranges
|
Detachment
|
|
Control panel, distributive panel and case
|
Zabivaniye of hydraulic channels
|
The indicator position of the selector does not correspond to the chosen range
|
TO CHECK
|
REASON
|
|
Selector drive
|
Adjustment violation
|
|
Spring and stopper roller
|
Breakage, absence
|
|
Weakening of an inhaling of a bolt
|
|
Zolotnik of the switch of ranges
|
Detachment from the stopper lever
|
Leakages of working liquid
To execute diagnostics of leakage of working liquid.
Foaming of working liquid
|
TO CHECK
|
REASON
|
|
Working liquid
|
Hit in working liquid of cooling liquid of the engine
|
|
Too high level of working liquid
|
|
Filter of working liquid
|
Zabiraniye
|
|
Existence of cracks
|
|
Filter consolidation
|
Leakage of liquid
|
|
Engine condition
|
Engine overheat
|
|
Car condition
|
Car overload
|
Vibration
|
TO CHECK
|
REASON
|
|
Hydrotransformer
|
Balancing violation
|
|
Breakages of internal details
|
|
Transmission and Engine
|
Shift from normal situation
|
|
Target shaft, semi-axes
|
Balancing violation
|
|
Wear or damage of plugs
|
|
Turbine shaft
|
Wear of plugs
|
|
Balancing violation
|
The friction clutch of blocking of the hydrotransformer, slipping or too slow inclusion of a friction clutch does not join
Possible code of malfunction:
– 502 Sensor of speed of the car – a low voltage of a signal
– 503 Sensor of speed of the car – an unstable or chaotic signal
– 703 Malfunction of the switch of a stoplight
– 712 Sensor of temperature of working liquid of transmission – a low voltage of a signal
– 713 Sensor of temperature of working liquid of transmission – a high voltage of a signal
– 716 Sensor of speed of rotation of an entrance shaft – low frequency of a signal
– 717 Sensor of speed of rotation of an entrance shaft – a signal is absent
– 741 Chain of management of a friction clutch of blocking of GT, EMK jamming in the switched-off situation
– 742 Chain of management of a friction clutch of blocking of GT, EMK jamming in the included situation
– 751 EMK of the switch A – the executive distributor
– 753 EMK of the switch A – the executive distributor
– 756 EMK of the switch B – the executive distributor
– 758 EMK of the switch B – refusal of an electric chain
– 1560 Deviation of tension of an electric network from norm
– 1810 Malfunction of the switch of control of ranges (blocking of the relay of pressure)
– 1812 Overheat of working liquid of transmission
– 1887 Relays of pressure of a friction clutch of blocking of GT
|
TO CHECK
|
REASON
|
|
EMK of a friction clutch of blocking of GT
|
Jamming in the switched-off situation
|
|
Leakage of working liquid through a sealing ring
|
|
Lack of tension on EMK winding
|
|
Transmission electroconducting
|
Bad electric contacts
|
|
Jamming wires (short circuit)
|
|
Damage of the electric socket
|
|
БУТ
|
Lack of an operating signal of EMK
|
Overheat of working liquid
|
TO CHECK
|
REASON
|
|
Hydrotransformer
|
Breakage of internal details
|
|
Hydraulic system of a friction clutch of blocking of GT
|
Leakage of working liquid
|
|
Hydrodistributors of management of a blocking friction clutch
|
Zolotnik jamming in the provision of switching off of a friction clutch of blocking
|
|
Level and pressure of working liquid
|
Low level or pressure of working liquid
|
The friction clutch of blocking is not switched off
|
TO CHECK
|
REASON
|
|
EMK of a friction clutch of blocking of GT
|
Jamming in the included situation
|
|
Blockage of a drain opening
|
|
Short circuit on "weight"
|
|
Hydrotransformer
|
Breakage of internal details
|
|
Hydrodistributors of management of a blocking friction clutch
|
Zolotnik jamming in the provision of switching off of a friction clutch of blocking
|
Premature blocking of the hydrotransformer before engine warming up
|
TO CHECK
|
REASON
|
|
The sensor of temperature of cooling liquid of the engine
|
Violation of normal work
|
Noise
|
MALFUNCTION SIGN
|
TO CHECK
|
REASON
|
|
On all ranges howling noise which depends on frequency of rotation of a shaft of the engine or disappears when blocking GT
|
Hydrotransformer
|
To check that a source of noise is GT. For this purpose at the included range of D to press one-times but for a brake pedal (the left foot) and a pedal of an accelerator and quickly to muffle the Engine. Noise of GT increases at increase in loading at GT
|
|
Howling noise of a high-pitch tone which increases at increase of turns of the engine or is sensitive to size of pressure of working liquid
|
Hydropump and its drive
|
To check that a source of noise is the hydropump (at the same time with pressure check in the trunk main). Increase of pressure brings to growth of noise of the hydropump
|
|
The sound similar to crackling of roasted corn grains
|
|
The hydropump works in a mode of cavitation which is shown available vials on щупе
|
|
Leakage of liquid through seams of the case of the filter
|
|
Damage or mixture from normal the provision of consolidation of the mesh filter
|
|
Rumble or jingling sound of a high-pitch tone
|
Condition of pipelines of the heat exchanger of working liquid of transmission Lack of a contact of pipelines with a surface of a radiator and with other tubes
|
To check existence pressure fluctuation the worker of liquid on trembling of an arrow of a manometer
|
|
The howling or roaring sound amplifying and decreasing depending on speed of the car: the most appreciable at dispersal with small acceleration
|
Knot of chain transfer
|
|
|
To check that a source of noise is the chain and/or asterisks. For this purpose it is necessary to press the left foot a brake pedal and to transfer the selector from a range of D R to a range. If noise stopped, to check the following
|
|
|
Chain
|
Chain lengthening
|
|
Conducting and conducted asterisks
|
Breakage or cut of teeths
|
|
Development of working surfaces of teeths
|
|
Development of an internal ring or bodies of a kacheniye of the needle bearing of a nave of an asterisk
|
|
Bearing damage
|
|
Noise of the main transfer (rumble), is most strongly shown at dispersal with small acceleration and/or at movement on turn
|
Supports of the leader and conducted asterisks
|
Development of an internal ring of the needle bearing of a nave of an asterisk
|
|
Knot of the main transfer
|
Wear of satellites or washers
|
|
– Gear wheels (solar, satellites) main transfer
|
Damage or wear of teeths
|
|
Differential case
|
|
|
– Semi-axial gear wheels of differential
|
|
|
Transmission noise on the 1st, 2nd, 3rd or 4th transfer
|
Solar gear wheel of the main transfer
|
Wear and fatigue failures of teeths of gear wheels
|
|
– Satellites of the main transfer
|
Damage of a persistent washer
|
|
Transmission noise only on some ranges
|
By means of the table of inclusion of frictional managing directors of elements to track a capacity tray through a transmission in an operating mode with the increased noise and to check the mechanisms loaded on the corresponding transfers and ranges
|
Wear or damage of gear wheels
|
|
|
